Nissan GT-R. Instruction — part 251

PWO-8

< REMOVAL AND INSTALLATION >

POWER SOCKET

CONSOLE POWER SOCKET : Exploded View

INFOID:0000000009163473

CONSOLE POWER SOCKET : Removal and Installation

INFOID:0000000009163474

REMOVAL

1.

Remove center console assembly. Refer to

IP-23, "Exploded View"

.

2.

Disconnect power socket connector (A).

3.

Pull out inner socket (1) by pushing the ring pawl (C) from the
inner socket hole (square) (B).

4.

Remove ring (2) from center console assembly while pressing
pawls.

INSTALLATION

Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and center console assembly.

1

: Inner socket

2

: Ring

JSMIA0561ZZ

D

: Cut out

JSMIA0656ZZ

RAX-2

< SYMPTOM DIAGNOSIS >

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

SYMPTOM DIAGNOSIS

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NVH Troubleshooting Chart

INFOID:0000000009163173

Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.

×

: Applicable

Reference

T

h

is

wo

rk i

s

rec

o

m

m

e

n

d

e

d

to

be

p

e

rfo

rme

d

by

G

T

-R ce

rti

fie

d NIS

SAN d

eal

er

.

T

h

is

wo

rk i

s

rec

o

m

m

e

n

d

e

d

to

be

p

e

rfo

rme

d

by

G

T

-R ce

rti

fie

d NIS

SAN d

eal

er

.

NVH in DLN

section.

NVH in DLN

section.

NVH

in

RAX and RSU sections.

Re

fe

r to

REAR AXL

E i

n

t

h

is cha

rt.

NVH in WT

section.

NVH in WT

section.

Re

fe

r to

DRIVE SHA

FT i

n

t

h

is cha

rt.

NVH in BR

section.

NVH in ST

section.

Possible cause and SUSPECTED PARTS

Ex

ce

ss

iv

e joi

nt an

gle

Jo

in

t sl

id

in

g

re

si

st

a

n

c

e

Im

ba

la

nc

e

Imp

rop

er i

ns

ta

lla

ti

o

n,

lo

os

en

es

s

Part

s int

e

rference

PROPELLER S

H

A

F

T

DIFF

ERENTIAL

REAR AX

LE A

N

D

REAR SUSPE

N

S

ION

REAR AX

LE

TIRE

ROAD WHEEL

DRIVE SHAFT

BRAKE

STE

E

RING

Symptom

DRIVE
SHAFT

Noise

×

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

×

REAR AXLE

Noise

×

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

×

Vibration

×

×

×

×

×

×

×

Shimmy

×

×

×

×

×

×

×

Judder

×

×

×

×

×

×

Poor quality ride or handling

×

×

×

×

×

PRECAUTIONS

RAX-3

< PRECAUTION >

C

E

F

G

H

I

J

K

L

M

A

B

RAX

N

O

P

PRECAUTION

PRECAUTIONS

Precaution for Working Range at a Regular Dealership

INFOID:0000000009188290

CAUTION:

The service items unmentioned on this instruction are recommended to be performed by a GT-R certified
NISSAN dealer. Because those service items require special equipment and a GT-R certified technical
staff who completed special training.

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000009163174

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Instruction.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

General Precautions

INFOID:0000000009163175

CAUTION:

After finishing servicing, check that all the tools and waste are stored in a customary place.

Была ли эта страница вам полезна?
Да!Нет
5 посетителей считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности