Nissan GT-R. Instruction — part 332
WW-20
< REMOVAL AND INSTALLATION >
FRONT WASHER NOZZLE AND TUBE
Unit: mm (in)
Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
1.
Front washer nozzle
2.
Passenger side blade rubber end
3.
Driver side blade rubber end
: Spray area
: Target spray position
Spray position
T
L
X
Y
S
A
29 (1.14)
448 (17.64)
20 (0.79)
50 (1.97)
25 (0.98)
B
34 (1.34)
235 (9.25)
20 (0.79)
20 (0.79)
10 (0.39)
C
−
18 (
−
0.71)
112 (4.41)
20 (0.79)
20 (0.79)
10 (0.39)
D
29 (1.14)
115 (4.53)
20 (0.79)
20 (0.79)
10 (0.39)
E
30 (1.18)
304 (11.97)
20 (0.79)
30 (1.18)
15 (0.59)
F
−
40 (
−
1.57)
237 (9.33)
20 (0.79)
60 (2.36)
30 (1.18)
G
35 (1.38)
197 (7.76)
20 (0.79)
30 (1.18)
15 (0.59)
H
30 (1.18)
73 (2.87)
20 (0.79)
20 (0.79)
10 (0.39)
I
−
17 (
−
0.67)
68 (2.68)
20 (0.79)
20 (0.79)
10 (0.39)
NNLIA0046ZZ
FRONT WIPER ARM
WW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER ARM
Exploded View
INFOID:0000000009161874
Removal and Installation
INFOID:0000000009161875
REMOVAL
1.
Operate the front wiper to move it to the auto stop position.
2.
Open the hood.
3.
Remove the front wiper arm caps.
4.
Remove the front wiper arm mounting nuts.
5.
Disconnect the front washer tube from the front washer joint.
6.
Raise front wiper arm, and remove front wiper arm from the vehicle.
INSTALLATION
1.
Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2.
Operate the front wiper motor to move the front wiper to the auto stop position.
3.
Adjust the front wiper blade position. Refer to
.
4.
Install the front wiper arm by tightening the mounting nuts.
5.
Connect the front washer tube to the front washer joint.
6.
Inject the washer fluid.
1.
Front wiper blade (RH)
2.
Front wiper arm (RH)
3.
Front wiper arm cap
4.
Front wiper arm (LH)
5.
Front wiper blade (LH)
Refer to
JPLIA1178GB
ELH0717D
WW-22
< REMOVAL AND INSTALLATION >
FRONT WIPER ARM
7.
Operate the front wiper to move it to the auto stop position.
8.
Check that the front wiper blades stop at the specified position.
9.
Install the front wiper arm caps.
Adjustment
INFOID:0000000009161876
WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of cowl top cover and the top of wiper blade center
Standard clearance
NOTE:
For the passenger side wiper arm the corresponding parts differ
according to the length of the wiper blade, and are distinguished by
the beginning number identification stamped on the portion indicated
by the arrow as shown in the figure.
R
: 35.1
±
7.5 mm (1.382
±
0.295 in)
L
: 46.9
±
7.5 mm (1.846
±
0.295 in)
JPLIA0082ZZ
Wiper blade
Beginning number
475 mm (18.70 in)
—
525 mm (20.67 in)
39
JMLIA3778ZZ
WIPER BLADE
WW-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER BLADE
Exploded View
INFOID:0000000009161877
Removal and Installation
INFOID:0000000009161878
REMOVAL
Remove the wiper blade from the wiper arm.
INSTALLATION
Install the front wiper blade to the wiper arm.
Replacement
INFOID:0000000009161879
1.
Hold the rip of old wiper refill (1) at the rear end of the wiper
blade with long-nose pliers, and pull out the wiper refill to the
direction (A).
2.
Insert the tip of new wiper refill (1) into the rear end of wiper
blade. Slide the wiper refill to the direction (A) while pressing the
wiper refill onto the wiper blade rear end.
NOTE:
• Insert the wiper refill to be held securely by tab (B) of wiper
blade.
• After the wiper refill is fully inserted, remove the holder
*
(2).
*
: Attached to service parts.
1.
Wiper refill
2.
Wiper blade
3.
Wiper arm
A.
Wiper blade end
B.
Wiper blade tip
JPLIA1587ZZ
JPLIA1583ZZ
JPLIA1584ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст