Nissan GT-R. Instruction — part 202
MA-30
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
3.
Screw oil filter instructionly until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to the specification.
OIL FILTER : Inspection
INFOID:0000000009161770
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check there is no leakage of engine oil.
3.
Stop the engine and wait for 5 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
SPARK PLUG
SPARK PLUG : Removal and Installation
INFOID:0000000009161771
REMOVAL
1.
Remove engine cover with power tool. Refer to
.
2.
Remove intake manifold collector. Refer to
CAUTION:
Mark the parts with paint in advance of the reinstallation to prevent misalignment between the
intake manifold collector and intake manifold.
3.
Remove ignition coil.
4.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
CAUTION:
Never drop or shock spark plug.
INSTALLATION
Installation is the reverse order of removal.
SPARK PLUG : Inspection
INFOID:0000000009161772
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
a
: 14 mm (0.55 in)
JPBIA0030ZZ
Spark plug (Standard type)
ENGINE MAINTENANCE
MA-31
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Never drop or shock spark plug.
• Never use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
• Measure spark plug gap. When it exceeds the limit, replace spark plug even if it is within the speci-
fied replacement mileage. Refer to
.
• Spark plug gap adjustment is not required between replace-
ment intervals.
THROTTLE CHAMBER
THROTTLE CHAMBER : Inspection
INFOID:0000000009161773
Visually inspect the throttle chamber for deposits and clean as necessary.
EVAP VAPOR LINES
EVAP VAPOR LINES : Inspection
INFOID:0000000009161774
1.
Visually inspect EVAP vapor lines for improper attachment and for cracks, damage, loose connections,
chafing and deterioration. Refer to
2.
Inspect fuel tank filler cap vacuum relief valve for clogging, sticking, etc.
Cleaner air pressure:
Less than 588 kPa (6 kg/cm
2
, 85 psi)
Cleaning time:
Less than 20 seconds
SMA773C
JPBIA0031ZZ
MA-32
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
CHASSIS MAINTENANCE
TRANSMISSION OIL
TRANSMISSION OIL : Inspection
INFOID:0000000009190111
LEAKAGE CHECK
• Visually check transmission assembly surrounding area (oil seal, drain plug, filler plug, transmission case,
etc.) for smears and leakage of transmission oil.
• Check also the leakage or bleeding around rear final drive. For rear final drive check, refer to
DIFFERENTIAL GEAR OIL : Inspection"
.
JSDIA2641ZZ
CHASSIS MAINTENANCE
MA-33
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• *1: When the oil drops
• *2: If oil leakage is detected, perform necessary procedures, check for oil leakage, and adjust oil level to the proper level.
• *3: When the oil does not drop
• *4: The grease applied to parking cable part can melt to generate a drop due to heat. Be careful not to confuse it with transmission oil
leakage.
CONDITION CHECK
Remove the filler plug, insert a finger into the filler hole, and judge the oil conditions from the transmission oil
applied to the inside of the transmission case.
CAUTION:
Be careful not to cut the finger with edges.
Status
Parts
Required operation
Reference
Oil leak-
age
*1, *2
Trans-
mission
assem-
bly (on-
board/
single
unit)
A: Mating surface between oil pan and
case
Check the seal surface condition. Replace the oil
pan gasket only if there is a non-standard condi-
tion. Check for oil leakage.
This work is
recom-
mened to be
performed
by GT-R cer-
tified NIS-
SAN dealer.
B: Park position switch
Check the mounting surface condition. Replace
the plain washer only if there is not any other mal-
functioning condition. Check for oil leakage.
• C: Heat exchanger & bracket mounting
surface and heat exchanger mounting
bolt
• D: Water hose connection (Engine cool-
ant)
• C: Check the seal surface condition. If it is nor-
mal, replace the O-ring of the part where oil
leakage arises and the single-use parts re-
moved during procedure. Check for oil leakage.
• D: Check the seal surface condition. If it is nor-
mal, replace the clamp of the part where engine
coolant leakage arises. Check for engine cool-
ant leakage.
E: Front oil seal
Check the oil seal mounting surface and sliding
surface condition. Replace the front oil seal only if
there is not any other malfunctioning condition.
Check for oil leakage.
F: Drain plug
Replace the drain plug. Check for oil leakage.
G: Filler plug
Replace the filler plug gasket. Check for oil leak-
age.
• H: Transmission harness connector
• I: Oil seal of parking lever
• J: Oil seal of companion flange (trans-
mission side) of main propeller shaft as-
sembly
• K: Transmission case joining portion
• L: AWD solenoid
Replace the transmission assembly.
This work is
recom-
mened to be
performed
by GT-R cer-
tified NIS-
SAN dealer.
M: 3rd-5th check pin
Replace the plain washer. Check for oil leakage.
Trans-
mission
assem-
bly (sin-
gle unit)
N: Filler plug
Replace the filler plug gasket. Check for oil leak-
age.
O: Transmission case joining portion
Replace the transmission assembly.
• P: Idler bolt
• Q: Plug
Replace the plain washer or O-ring. Check for oil
leakage.
R: Breather
Clean and wipe spouted oil with a part cleaner. Fill
with oil to the specified oil level, if necessary.
—
Oil
smears
*3
Each part of the transmission assembly, including the
parts requiring oil leakage check.
Use part cleaner or the equivalent to wipe out
smeared oil. Then, check for oil leakage.
—
Grease
drop
*4
S: Parking cable
Wipe excess grease off.
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст