Nissan GT-R. Instruction — part 167
HAC-30
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONER]
SUNLOAD SENSOR
SUNLOAD SENSOR
Exploded View
INFOID:0000000009164059
Removal and Installation
INFOID:0000000009164060
REMOVAL
1.
Remove front defroster grille (left) (1), using remover tools (A).
Refer to
.
2.
Disconnect sunload sensor connector, and then remove sunload
sensor (2).
INSTALLATION
Installation is basically the reverse order of removal.
1.
Sunload sensor
2.
Front defroster grille (left)
3.
Instrument panel assembly
NNIIA0136ZZ
NNIIA0137ZZ
DOOR MOTOR
HAC-31
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
DOOR MOTOR
Exploded View
INFOID:0000000009164065
INTAKE DOOR MOTOR
INTAKE DOOR MOTOR : Removal and Installation
INFOID:0000000009164066
REMOVAL
1.
Remove instrument panel (assist). Refer to
.
1.
Air mix door motor (driver side)
2.
Air mix door motor adapter
3.
Heater & cooling unit assembly
4.
Ventilator door lever
5.
Foot door lever
6.
Foot door link
7.
Air mix door motor adapter
8.
Air mix door motor (passenger side) 9.
Ventilator door link
10. Blower unit
11.
Intake door lever 2
12. Intake door motor
13. Intake door link
14.
Intake door lever 1
15. Mode door motor
16. Mode door motor bracket
17.
Main link
18. Main link sub
19. Max.cool door link
20.
Defroster door link
21. Max.cool door lever
22. Defroster door lever
JSIIA1425ZZ
HAC-32
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONER]
DOOR MOTOR
2.
Remove mounting nuts (A).
3.
Disconnect ECM connectors, and then remove ECM (1) with
bracket attached.
4.
Remove power steering control unit. (This work should be performed by GT-R certified NISSAN dealer.).
5.
Remove mounting screws of intake door motor, and then remove intake door motor from blower unit.
6.
Disconnect intake door motor connector.
INSTALLATION
Installation is basically the reverse order of removal.
MODE DOOR MOTOR
MODE DOOR MOTOR : Removal and Installation
INFOID:0000000009164067
REMOVAL
1.
Remove blower unit. Refer to
2.
Remove mounting screws of mode door motor, and then remove mode door motor from heater & cooling
unit assembly.
3.
Disconnect mode door motor connector.
INSTALLATION
installation is basically the reverse order of removal.
AIR MIX DOOR MOTOR
AIR MIX DOOR MOTOR : Removal and Installation
INFOID:0000000009164068
REMOVAL
Driver Side
1.
Set the temperature (driver side) at 18.0
°
C (60
°
F).
2.
Disconnect the battery cable from the negative terminal.
CAUTION:
The angle may be out, when installing the air mix door motor to the air mix door, unless the above
2 procedures are performed.
3.
Remove instrument lower panel (driver). Refer to
4.
Remove mounting screws of air mix door motor, and then remove air mix door motor.
5.
Disconnect air mix door motor connector.
Passenger Side
1.
Set the temperature (passenger side) at 18.0
°
C (60
°
F).
2.
Disconnect the battery cable from the negative terminal.
CAUTION:
The angle may be out, when installing the air mix door motor to the air mix door, unless the above
2 procedures are performed.
3.
Remove instrument lower panel (assist). Refer to
.
4.
Remove mounting screws of air mix door motor, and then remove air mix door motor.
5.
Disconnect air mix door motor connector.
INSTALLATION
JSIIA1196ZZ
DOOR MOTOR
HAC-33
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Installation is basically the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст