Nissan GT-R. Instruction — part 187
INSTRUMENT PANEL ASSEMBLY
IP-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
1.
Remove fixing screws (A).
2.
Pull back out instrument lower panel (assist) (1).
3.
Disconnect harness connector of back side and remove
harness clamp.
40. Remove instrument pad C.
Pull instrument pad C (1) in order from 1 - 3, and then disengage
metal clips.
41. Disconnect harness connector of passenger air bag module. Refer to
.
42. Remove passenger air bag module mounting bolt. Refer to
SR-17, "Removal and Installation"
43. Remove instrument panel assembly.
1.
Remove mounting bolt (A) of instrument side bracket (1).
2.
Remove mounting bolt (B) of instrument panel assembly (2).
3.
Remove fixing screw (C) of instrument panel assembly.
4.
Remove front defroster nozzle mounting clip (D).
CAUTION:
Cover tool with a shop cloth to prevent windshield glass from being damaged.
5.
Pull out instrument panel assembly toward rear of vehicle, and then remove it from door opening.
CAUTION:
When removing instrument panel assembly, 2 workers are required to prevent it from drop-
ping.
44. Remove following parts after removing instrument panel assembly.
• Passenger air bag module: Refer to
SR-17, "Removal and Installation"
.
• GPS antenna (BOSE audio with NAVI models): Refer to
AV-184, "Removal and Installation"
.
• Antenna feeder
JMJIA2196ZZ
: Metal clip
JMJIA2197ZZ
JMJIA2198ZZ
IP-22
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
- BASE audio with NAVI models: Refer to
- BOSE audio with NAVI models: Refer to
.
• Monitor bracket
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use steering wheel mounting nut after removal, replace with new nut.
• Never use driver air bag module mounting bolts after removal, replace with new bolts.
• Never use passenger air bag module mounting bolt after removal, replace with new bolt.
CENTER CONSOLE ASSEMBLY
IP-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
CENTER CONSOLE ASSEMBLY
Exploded View
INFOID:0000000009162797
Removal and Installation
INFOID:0000000009162798
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
1.
Remove rear console assembly.
1.
Rear console assembly
2.
Console lid
3.
Cup holder finisher
4.
Parking brake lever boot
5.
Instrument side panel RH
6.
Console finisher assembly
7.
Cup holder assembly
8.
Instrument side panel LH
9.
Console bracket
10. Inside key antenna
11.
Center console assembly
12. USB connector
13. Socket knob
14. Power socket
JMJIA3736ZZ
IP-24
< REMOVAL AND INSTALLATION >
CENTER CONSOLE ASSEMBLY
1.
Lift up rear side of rear console assembly (1), and then dis-
engage pawls and metal clips.
2.
Disconnect harness connector on the back.
2.
Remove instrument garnish LH.
1.
Insert remover tool (A), wrapped in a shop cloth, into clear-
ance between lower side of instrument garnish LH (1) and
cluster lid C (lower) (2).
2.
Pull back instrument garnish LH, and then disengage pawls.
3.
Remove instrument garnish RH.
1.
Insert remover tool (A), wrapped in a shop cloth, into clear-
ance between lower side of instrument garnish RH (1) and
cluster lid C (lower) (2).
2.
Pull back instrument garnish RH, and then disengage
pawls.
4.
Remove console finisher.
1.
Open console lid.
2.
Insert remover tool (A) between console finisher (1) and
center console, lift up console finisher, and then disengage
clips and pawls.
5.
Remove instrument side panel LH.
: Pawl
: Metal clip
NNJIA0052ZZ
: Pawl
JMJIA2177ZZ
: Pawl
JMJIA2176ZZ
: Clip
: Pawl
JMJIA2178ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст