Nissan Titan. Instruction — part 574
ST-32
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Power Steering Gear
INFOID:0000000009883518
Power Steering Oil Pump
INFOID:0000000009883519
Power Steering Fluid
INFOID:0000000009883520
Steering gear model
PR26AM
Rack neutral position, dimension (L) (rack stroke)
85.5 mm (3.36 in)
Rack sliding force
Standard
308
± 45 N (31.4 ± 4.6 kg-f, 69.2 ± 10.1 lb-f)
Service limit (Minimum)
240 N (24.5 kg-f, 54.0 lb-f)
STC0034D
Relief oil pressure
9.0
− 9.8 mPa (91.77 − 99.93 kg/cm
2
, 1305.34
− 1421.37 psi)
Power steering fluid capacity
Approx. 1.0 (1-1/8 US qt, 7/8 Imp qt)
STR-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
STR
A
STR
N
O
P
CONTENTS
STARTING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Power Generation Variable Voltage
Control System . . . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
Work Flow (With GR8-1200 NI) . . . . . . . ....
Work Flow (Without GR8-1200 NI) . . . . . . ...
SYSTEM DESCRIPTION . . . . . . . .
STARTING SYSTEM . . . . . . . . . . ..
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ..
DTC/CIRCUIT DIAGNOSIS . . . . . . .
B TERMINAL CIRCUIT . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
S CONNECTOR CIRCUIT . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ..
STARTING SYSTEM . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . . ..
STARTING SYSTEM . . . . . . . . . . .
Symptom Table . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ...
STARTER MOTOR . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
STR-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009886973
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Power Generation Variable Voltage Control System
INFOID:0000000009886974
CAUTION:
For this model, the battery current sensor that is installed to the negative battery cable measures the
charging/discharging current of the battery and performs various engine controls. If an electrical com-
ponent is connected directly to the negative battery terminal, the current flowing through that compo-
nent will not be measured by the battery current sensor. This condition may cause a malfunction of
the engine control system and battery discharge may occur. Do not connect an electrical component
or ground wire directly to the battery terminal.
PREPARATION
STR-3
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009886975
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000009886976
Tool number
(Kent-Moore No.)
Tool name
Description
—
(—) Model GR8-1200 NI
Multitasking battery and electrical di-
agnostic station
Tests batteries, starting and charging sys-
tems and charges batteries.
For operating instructions, refer to diagnostic
station instruction instruction.
AWIIA1239ZZ
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст