Nissan Titan. Instruction — part 486
REAR POWER WINDOW SWITCH
PWC-117
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REAR POWER WINDOW SWITCH
Removal and Installation - Rear Door Switch
INFOID:0000000009879042
REMOVAL
1. Remove the rear door switch finisher (1) and rear door switch (2) from the rear door finisher using a suit-
able tool.
• Disconnect the rear door switch harness connector.
2. Release the tabs using suitable tool (A) and remove the switch
(2).
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation - Power Drop Glass Switch
INFOID:0000000009879043
REMOVAL
1. Release the pawls and remove the overhead console switch fin-
isher (1) from overhead console using a suitable tool (A).
: Pawl
2. Release the tabs and remove power drop glass switch from the
overhead console switch finisher (1) using suitable tool (A).
INSTALLATION
Installation is in the reverse order of removal.
ALKIA0860ZZ
ALKIA1936ZZ
RAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
RAX
A
B
RAX
N
O
P
CONTENTS
REAR AXLE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
General Precautions . . . . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION, AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
BASIC INSPECTION . . . . . . . . .
AXLE SHAFT . . . . . . . . . . . . . .
On-Vehicle Inspection . . . . . . . . . . . ..
UNIT REMOVAL AND INSTALLATION . ...
AXLE OIL SEAL . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . ..
AXLE BEARING . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . ..
AXLE SHAFT . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
RAX-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009886180
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
General Precautions
INFOID:0000000009886181
When installing rubber parts, final tightening must be carried out under unladen condition* with tires
on ground.
* Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated posi-
tions.
PREPARATION
RAX-3
< PREPARATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009886182
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000009886183
Tool number
(Kent-Moore No.)
Tool name
Description
KV40101000
(J-25604-01)
Axle stand
Removing axle shaft
ST36230000
(J-25840-A)
Slide hammer
Removing axle shaft
ST30031000
( — )
Bearing splitter
Removing axle shaft bearing
NT159
NT126
ZZA0700D
Tool name
Description
Power tools
Loosening nuts, screws and bolts
PIIB1407E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст