Nissan Titan. Instruction — part 142
DLN-140
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2S1410]
PROPELLER SHAFT
• Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly. Refer to
•
: Front
• While holding the flange yoke on one side, check axial play of the
joint as shown. If the journal axial play exceeds the specification,
repair or replace the journal parts. Refer to
• Check the propeller shaft tube for dents or cracks. If damage is
detected, replace the propeller shaft assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, check for vibration by driving the vehicle. Refer to
DLN-137, "NVH Troubleshooting Chart"
.
• If propeller shaft assembly or final drive assembly has been
replaced, connect them as follows:
- Face companion flange mark (A) of the final drive (1) upward. With
the mark (A) faced upward, couple the propeller shaft and the final
drive so that the matching mark (B) of the propeller shaft (2) can be
positioned as closest as possible with the matching mark (C) of the
final drive companion flange.
- Tighten propeller shaft and final drive bolts and nuts to specifica-
DLN-139, "Removal and Installation"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
AWDIA0037ZZ
LDIA0117E
PDIA0892J
PROPELLER SHAFT
DLN-141
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 2S1410]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
PROPELLER SHAFT
Disassembly and Assembly
INFOID:0000000009886058
DISASSEMBLY
Journal
1. Put matching marks on the rear propeller shaft and flange yoke
as shown.
CAUTION:
For matching marks use paint. Do not damage the rear pro-
peller shaft or flange yoke.
2. Remove the snap rings.
CAUTION:
Do not reuse snap rings.
3. Push out and remove the journal bearings by lightly tapping the
flange yoke with a hammer, taking care not to damage the jour-
nal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
4. Push out and remove the remaining journal bearings at the
opposite side by lightly tapping the flange yoke with a hammer,
taking care not to damage the journal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
ASSEMBLY
SPD128
APD011
SPD732
SPD131
DLN-142
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 2S1410]
PROPELLER SHAFT
Journal
1. Assemble the journal bearings. Apply multipurpose grease on
the bearing inner surface.
NOTE:
During assembly, use caution so that the needle bearings do not
fall down.
2. Select new snap rings that will provide the specified play in an
axial direction of the journal, and install them. Refer to
.
CAUTION:
Do not reuse snap rings
NOTE:
Select snap rings with a difference in thickness at both sides
within 0.02 mm (0.0008 in).
3. Adjust the thrust clearance between the bearing and snap ring
to zero by tapping the yoke.
4. Make sure that the journal moves smoothly and is below the
propeller joint flex effort specification. Refer to
.
WPD019
APD012
SPD732
LDIA0119E
SERVICE DATA AND SPECIFICATIONS (SDS)
DLN-143
< SERVICE DATA AND SPECIFICATIONS (SDS)
[PROPELLER SHAFT: 2S1410]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000009886059
Unit: mm (in)
PROPELLER SHAFT RUNOUT
Unit: mm (in)
PROPELLER SHAFT JOINT FLEX EFFORT
Unit: N·m (kg-m, in-lb)
JOURNAL AXIAL PLAY
Unit: mm (in)
Snap Ring
INFOID:0000000009886060
Unit: mm (in)
*Always check with the Parts Department for the latest parts information.
Applied model
4WD
SWB
Propeller shaft model
2S1410
Number of joints
2
Coupling method with rear final drive
Flange type
Coupling method with Transfer
Sleeve type
Installed shaft length (Spider to spider)
1616.2
± 1.5 (63.63 ± 0.06)
Shaft outer diameter
127.6 + 0.22 - 0.29 (5.02
± 0.01)
Item
Limit
Propeller shaft runout
1.02 (0.0402) or less
Item
Limit
Propeller shaft joint flex effort
2.26 (0.23, 20) or less
Item
Limit
Journal axial play
0.02 (0.0008) or less
Thickness
Color
Part Number*
1.600 - 1.638 (0.0630 - 0.0645)
Black
37146-EA500
1.549 - 1.588 (0.0610 - 0.0625)
Black
37147-EA500
1.524 - 1.562 (0.0600 - 0.0615)
Black
37148-EA500
1.499 - 1.537 (0.0590 - 0.0605)
Black
37149-EA500
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст