Nissan Titan. Instruction — part 543
SR-12
< REMOVAL AND INSTALLATION >
SIDE CURTAIN AIR BAG MODULE
King Cab
REMOVAL
CAUTION:
• Do not attempt to repair or replace damaged direct-connect SRS component connectors. If a direct-
connect harness connector is damaged, the harness must be replaced.
• Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals and wait at
least three minutes.
• When servicing the SRS, do not work from directly in front of air bag module.
• Do not insert any foreign objects (screwdriver, etc.) into air bag module or harness connectors.
• Do not disassemble air bag module.
• Do not expose the air bag module to temperatures exceeding 90
°C (194°F).
• Replace side curtain air bag module if it has been dropped or
sustained an impact.
• Do not allow oil, grease or water to come in contact with the
air bag module.
1. Disconnect both the negative and positive battery terminals,
then wait at least three minutes. Refer to
.
2. Remove headlining. Refer to
INT-21, "Removal and Installation"
.
3. Disconnect side curtain air bag module connector.
• For removal/installation of the direct-connect SRS connectors,
SRC-9, "Direct-connect SRS Component Connectors"
.
4. Remove the bolts in order starting at the front or rear, and remove the side curtain air bag module.
INSTALLATION
Installation is in the reverse order of removal.
• For removal/installation of the direct-connect SRS connectors, refer to
SRC-9, "Direct-connect SRS Compo-
• After replacement of side curtain air bag module, perform self-diagnosis to check that no malfunction is
.
ALHIA0208GB
1.
Side curtain air bag module inflator 2.
Side curtain air bag module A.
Side curtain air bag module
harness connector
SBF814E
SIDE AIR BAG MODULE
SR-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE AIR BAG MODULE
Removal and Installation
INFOID:0000000009882848
For side air bag module removal and installation, the front seatback must be disassembled, refer to
.
NOTE:
If the vehicle has been involved in a collision and the side air bag has deployed, the front seatback assembly
must be replaced.
SR-14
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Removal and Installation
INFOID:0000000009882849
REMOVAL
CAUTION:
• Before servicing the SRS, turn the ignition switch off, disconnect both battery cables and wait at
least three minutes.
• Replace crash zone sensor if it has been dropped or sustained an impact.
• Do not disassemble crash zone sensor.
1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove front grille. Refer to
EXT-20, "Removal and Installation"
3. Disconnect the harness connector from the crash zone sensor.
4. Remove crash zone sensor nuts.
INSTALLATION
Installation is in the reverse order of removal.
• After the work is complete, perform self-diagnosis to check that no malfunction is detected. Refer to
LHIA0056E
SIDE AIR BAG (SATELLITE) SENSOR
SR-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE AIR BAG (SATELLITE) SENSOR
Removal and Installation
INFOID:0000000009882850
REMOVAL
CAUTION:
• Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals and wait at
least three minutes.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes. Refer to
80, "Removal and Installation"
2. For Crew Cab models, remove seat belt retractor assembly.
Refer to
SB-4, "Removal and Installation of Front Seat Belt"
. For
King Cab models, remove kicking plates and pull back carpet.
3. Remove side air bag (satellite) sensor nuts.
4. Disconnect the side air bag (satellite) sensor harness connector.
CAUTION:
• Do not use old nuts after removal; replace with new nuts.
• Check side air bag (satellite) sensor to ensure it is free of deformities, dents, cracks or rust. If it
shows any visible signs of damage, replace it with new one.
• Do not disassemble side air bag (satellite) sensor.
• Replace side air bag (satellite) sensor if it has been dropped or sustained an impact.
INSTALLATION
Installation is in the reverse order of removal.
• After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
LHIA0062E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст