Nissan Titan. Instruction — part 139
DLN-128
< SYSTEM DESCRIPTION >
[PROPELLER SHAFT: 2F1310]
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
SYSTEM DESCRIPTION
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009886047
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
"
Possible cause and suspected parts
Un
ev
en
rot
ati
on
torq
ue
Ro
ta
tion
im
ba
la
nc
e
Ex
ce
ss
iv
e run
ou
t
Di
ffere
n
tial
Axle
Su
sp
en
si
on
Ti
re
s
Road wheel
Driv
e sh
af
t
Brak
es
St
ee
rin
g
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
PROPELLER SHAFT
DLN-129
< REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2F1310]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
PROPELLER SHAFT
On-Vehicle Service
INFOID:0000000009886048
APPEARANCE AND NOISE INSPECTION
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace the propeller shaft assembly.
• Check the bearings for noise and damage. Repair or replace the bearings as necessary.
PROPELLER SHAFT VIBRATION
If a vibration is present at high speed, inspect the propeller shaft runout first.
1. Measure the runout of the propeller shaft tube at several points
by rotating the final drive companion flange with your hands.
DLN-134, "General Specification"
.
2. If the runout exceeds specifications, disconnect the propeller
shaft at the final drive companion flange; then rotate the com-
panion flange 90
°, 180° and 270° and reconnect the propeller
shaft.
3. Check the runout again. If the runout still exceeds specifications,
replace the propeller shaft assembly. Refer to
.
4. After installation, check for vibration by driving the vehicle.
LDIA0160E
LDIA0118E
DLN-130
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2F1310]
PROPELLER SHAFT
UNIT REMOVAL AND INSTALLATION
PROPELLER SHAFT
Removal and Installation
INFOID:0000000009886049
COMPONENTS
REMOVAL
1. Remove under covers (if equipped).
2. Put matching marks on the front propeller shaft flange yoke and
the front final drive companion flange as shown.
CAUTION:
For matching marks, use paint. Do not damage the flange
yoke and companion flange of the front final drive.
3. Put matching marks on the front propeller shaft flange yoke and
the transfer companion flange.
CAUTION:
For matching marks, use paint. Do not damage the flange
yoke and companion flange of the front final drive.
4. Remove the bolts and then remove the front propeller shaft from
the front final drive and transfer.
INSPECTION
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Journal
5.
Flange yoke
Front
WDIA0304E
SDIA2046E
PROPELLER SHAFT
DLN-131
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2F1310]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly. Refer to
• While holding the flange yoke on one side, check axial play of the
joint as shown. If the journal axial play exceeds the specification,
repair or replace the journal parts. Refer to
• Check the propeller shaft tube surface for dents or cracks. If dam-
age is detected, replace the propeller shaft assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, check for vibration by driving the vehicle. Refer to
DLN-128, "NVH Troubleshooting Chart"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
LDIA0118E
LDIA0117E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст