Nissan Titan. Instruction — part 102
PREPARATION
DLK-117
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Commercial Service Tool
INFOID:0000000009878834
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear
Locating the noise
SIIA0995E
DLK-118
< REMOVAL AND INSTALLATION >
HOOD
REMOVAL AND INSTALLATION
HOOD
Fitting Adjustment
INFOID:0000000009878835
AWKIA2077ZZ
HOOD
DLK-119
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CLEARANCE AND SURFACE HEIGHT ADJUSTMENT
1. Remove the front grille. Refer to
EXT-20, "Removal and Installation"
2. Remove the hood lock assembly and adjust the height by rotating the bumper rubber until the hood clear-
ance of hood and fender becomes 1 mm (0.04 in) lower than fitting standard dimension.
3. Temporarily tighten the hood lock, and position it by engaging it with the hood striker. Check the lock and
striker for looseness, and tighten the lock bolt to the specified torque.
4. Adjust the clearance and surface height of hood and fender according to the fitting standard dimension by
rotating right and left bumper rubbers.
CAUTION:
Adjust right/left gap between hood and each part to the following specification.
5. Install the front grille. Refer to
EXT-20, "Removal and Installation"
.
HOOD LOCK ADJUSTMENT
1. Remove the front grille. Refer to
EXT-20, "Removal and Installation"
.
2. Move the hood lock to the left or right so that striker center is vertically aligned with hood lock center
(when viewed from vehicle front).
3. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height or by pressing it lightly approx.
3 kg (29 N, 7lb).
CAUTION:
Do not drop the hood from 300 mm (11.81 in) height or
higher.
4. After adjusting hood lock, tighten the lock bolts to the specified
torque.
5. Install the front grille. Refer to
EXT-20, "Removal and Installa-
Removal and Installation of Hood Assembly
INFOID:0000000009878836
CAUTION:
• Use two people when removing or installing hood assembly due to its heavy weight.
• Use protective tape or shop cloths to protect surrounding components from damage during removal
and installation of hood assembly.
REMOVAL
1. Support the hood assembly using a suitable tool.
WARNING:
Bodily injury may occur if hood assembly is not supported properly when removing hood assem-
bly.
1.
Hood hinge
2.
Hood stay
3.
Hood lock assembly
4.
Hood assembly
5.
Front grille
6.
Headlamp
7.
Front fender
E.
2.0 mm (0.079 in)
F.
8.0mm (0.315 in)
G.
0.8 mm (0.031 in)
H.
5.0 mm (0.197 in)
J.
0.0 mm (0.00 in)
K.
8.0 mm (0.315 in)
L.
8.8 mm (0.346 in)
Hood and headlamp (B–B)
8.0
± 2.0 mm (0.315 ± 0.079 in)
PIIA3806E
DLK-120
< REMOVAL AND INSTALLATION >
HOOD
2. Remove the hinge nuts (
) and the hood assembly.
INSTALLATION
Installation is in the reverse order of removal.
• Adjust the hood. Refer to
.
• Adjust the hood lock. Refer to
Removal and Installation of Hood Lock Control
INFOID:0000000009878837
REMOVAL
1. Remove the hood lock assembly bolts.
2. Disconnect the hood lock release cable from the hood lock assembly, and unclip it from the radiator core
support upper and hoodledge.
3. Remove the bolt and the hood lock release handle.
4. Remove the grommet from the dash lower, and pull the hood lock release cable toward the passenger
compartment.
CAUTION:
While pulling, be careful not to damage the outside of the hood lock release cable, keep the radius
100mm (3.94 in) or more.
5. Remove the hood lock assembly.
WIIA0885E
1.
Hood lock assembly
2.
Hood lock release cable
AWKIA2072ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст