Nissan Titan. Instruction — part 337
EXT-18
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Removal and Installation
INFOID:0000000009879095
1.
Rear bumper reinforcement
2.
Sonar sensor harness (if equipped)
3.
Sonar sensor (if equipped)
4.
License lamp harness
5.
Upper step pad
6.
License lamp clip
7.
Carriage bolt
8.
Rear bumper
9.
Sonar sensor retainer (if equipped)
AWKIA1535GB
REAR BUMPER
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REMOVAL
1. Disconnect the sonar sensor harness connector (if equipped).
• Disconnect the sonar sensors from retainers.
2. Disconnect the license lamp harness.
3. Remove the clips from the license lamps and remove lamps.
4. Release the clips and remove the upper step pads.
5. Remove the rear bumper reinforcement bolts and remove the rear bumper.
6. Disconnect the harness clips from the black steel bumper.
7. Remove the sonar sensor retainers from the rear bumper (if equipped).
8. Remove the sonar sensors and harness from the rear bumper (if equipped).
• Disconnect the sonar sensors from harness.
9. Remove the license lamp harness from the rear bumper.
INSTALLATION
Installation is in the reverse order of removal.
• Apply sealant to clips securing upper step pad during installation.
10. License lamp
11. License lamp washer
12. Lower step pad
13. Tow hitch (if equipped)
EXT-20
< REMOVAL AND INSTALLATION >
FRONT GRILLE
FRONT GRILLE
Removal and Installation
INFOID:0000000009879096
REMOVAL
1. Release the plastic clips and remove the front grille.
2. Remove the (LH/RH) front bumper filler panels.
3. Remove the front emblem (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
1.
Plastic clip
2.
Plastic clip
3.
Grommet
4.
Front bumper filler panel (RH)
5.
Front grille
6.
Front bumper filler panel (LH)
WIIA0986E
COWL TOP
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
COWL TOP
Removal and Installation
INFOID:0000000009879097
REMOVAL
1. Remove the right and left wiper arms. Refer to
.
2. Remove the cowl top seal.
• Release the plastics clips on the cowl top seal which go through the cowl tops (LH/RH) and cowl top
extension.
3. Remove the cowl top covers (LH/RH).
• Release the plastic clips under cowl top covers attaching to grommets on hoodledge.
• Disconnect the washer tubes from washer nozzles.
4. Remove the cowl top extension brackets (LH/RH).
• Disconnect the wiper motor harness from cowl top extension bracket (LH).
• Cowl top extension bracket (LH) must be removed prior to removal of the wiper motor and connecting
rod assembly.
5. Remove the wiper motor and connecting rod linkage. Refer to
WW-54, "Wiper Motor and Linkage"
.
1.
Grommet
2.
Plastic clip 3.
Cowl
top
(RH)
4.
Cowl top seal
5.
Drain tube
6.
Cowl top extension bracket (RH)
7.
Cowl top extension
8.
Cowl top extension bracket (LH)
9.
Cowl top (LH)
WIIA0987E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст