Nissan Pathfinder (2009 year). Instruction — part 280
EC-254
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0448 EVAP CANISTER VENT CONTROL VALVE
DRAIN FILTER
1.
Check visually for insect nests in the drain filter air inlet.
2.
Check visually for cracks or flaws in the appearance.
3.
Check visually for cracks or flaws in the hose.
4.
Blow air into port A and check that it flows freely out of port B.
5.
Block port B.
6.
Blow air into port A and check that there is no leakage.
7.
If NG, replace drain filter.
PBIB3641E
2009 Pathfinder
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-255
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
Component Description
INFOID:0000000004297444
The EVAP control system pressure sensor (2) detects pressure in
the purge line. The sensor output voltage to the ECM increases as
pressure increases.
• Fuel filler pipe (top of frame view) (1)
• EVAP canister vent control valve (3)
• EVAP canister (4)
• Drain filter (5)
•
: Vehicle front
On Board Diagnosis Logic
INFOID:0000000004297445
If DTC P0451 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to
.
DTC Confirmation Procedure
INFOID:0000000004297446
1.
If DTC Confirmation Procedure has been previously conducted, always perform the following before con-
ducting the next step.
a.
Turn ignition switch OFF and wait at least 10 seconds.
b.
Turn ignition switch ON.
c.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Start engine and wait at least 40 seconds.
NOTE:
Do not depress accelerator pedal even slightly.
3.
Check 1st trip DTC.
4.
If 1st trip DTC is detected, go to
Diagnosis Procedure
INFOID:0000000004297447
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
AWBIA0134ZZ
PBIB3370E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0451
0451
EVAP control system
pressure sensor perfor-
mance
ECM detects a sloshing signal from the EVAP
control system pressure sensor
• Harness or connectors
• EVAP control system pressure sensor
2009 Pathfinder
EC-256
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
2.
Loosen and retighten three ground screws on the body. Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
2.
CHECK EVPA CONTROL SYSTEM PRESSURE SENSOR CONNECTOR FOR WATER
1.
Disconnect EVAP control system pressure sensor (2) harness
connector.
-
Fuel filler pipe (top of frame view) (1)
-
EVAP canister vent control valve (3)
-
EVAP canister (4)
-
Drain filter (5)
-
: Vehicle front
2.
Check sensor harness connector for water.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness connector.
3.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-256, "Component Inspection"
OK or NG
OK
>> GO TO 4.
NG
>> Replace EVAP control system pressure sensor.
4.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000004297448
EVAP CONTROL SYSTEM PRESSURE SENSOR
1.
Remove EVAP control system pressure sensor with its harness connector connected from EVAP canister.
Do not reuse the O-ring, replace it with a new one.
2.
Install a vacuum pump to EVAP control system pressure sensor.
BBIA0539E
Water should not exist.
AWBIA0134ZZ
2009 Pathfinder
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-257
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3.
Turn ignition switch ON and check output voltage between ECM
terminal 32 and ground under the following conditions.
CAUTION:
• Always calibrate the vacuum pump gauge when using it.
• Never apply below -93.3 kPa (-0.952 kg/cm
2
, -13.53 psi) or
pressure over 101.3 kPa (1.033 kg/cm
2
, 14.69 psi).
4.
If NG, replace EVAP control system pressure sensor.
Applied vacuum kPa
(kg/cm
2
, psi)
Voltage V
Not applied
1.8 - 4.8
-26.7 (-0.272, -3.87)
2.1 to 2.5V lower than above value
PBIB1173E
2009 Pathfinder
EC-258
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
Component Description
INFOID:0000000004297449
The EVAP control system pressure sensor (2) detects pressure in
the purge line. The sensor output voltage to the ECM increases as
pressure increases.
• Fuel filler pipe (top of frame view) (1)
• EVAP canister vent control valve (3)
• EVAP canister (4)
• Drain filter (5)
•
: Vehicle front
On Board Diagnosis Logic
INFOID:0000000004297450
If DTC P0452 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to
.
DTC Confirmation Procedure
INFOID:0000000004297451
NOTE:
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next step.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Always perform test at a temperature of 5
°
C (41
°
F) or more.
WITH CONSULT-III
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON.
4.
Turn ignition switch OFF and wait at least 10 seconds and then turn ON.
5.
Select “DATA MONITOR” mode with CONSULT-III.
6.
Make sure that “FUEL T/TMP SE” is more than 0
°
C (32
°
F).
7.
Start engine and wait at least 20 seconds.
8.
Check 1st trip DTC.
AWBIA0134ZZ
PBIB3370E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0452
0452
EVAP control system
pressure sensor low in-
put
An excessively low voltage from the sensor is
sent to ECM.
• Harness or connectors
(The sensor circuit is open or shorted.)
• EVAP control system pressure sensor
2009 Pathfinder
P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-259
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
9.
If 1st trip DTC is detected, go to
WITH GST
1.
Start engine and warm it up to normal operating temperature.
2.
Check that voltage between ECM terminal 107 (Fuel tank tem-
perature sensor signal) and ground is less than 4.2V.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Turn ignition switch ON.
5.
Turn ignition switch OFF and wait at least 10 seconds.
6.
Start engine and wait at least 20 seconds.
7.
Select Service $07 with GST.
If 1st trip DTC is detected, go to
Diagnosis Procedure
INFOID:0000000004297452
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body. Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
2.
CHECK CONNECTOR
1.
Disconnect EVAP control system pressure sensor (2) harness
connector.
-
Fuel filler pipe (top of frame view) (1)
-
EVAP canister vent control valve (3)
-
EVAP canister (4)
-
Drain filter (5)
-
: Vehicle front
2.
Check sensor harness connector for water.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness connector.
3.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
PBIB1110E
BBIA0539E
Water should not exist.
AWBIA0134ZZ
2009 Pathfinder
EC-260
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
2.
Check voltage between EVAP control system pressure sensor
terminal 3 and ground with CONSULT-III or tester.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors C1, E41
• Harness connectors E5, F14
• Harness for open or short between EVAP control system pressure sensor and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between EVAP control system pressure sensor terminal 1 and ECM terminal
67.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors C1, E41
• Harness connectors E5, F14
• Harness for open or short between EVAP control system pressure sensor and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND
SHORT
1.
Check harness continuity between ECM terminal 32 and EVAP control system pressure sensor terminal
2.
Refer to Wiring Diagram.
2.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors C1, E41
• Harness connectors E5, F14
Voltage: Approximately 5V
PBIB0138E
Continuity should exist.
Continuity should exist.
2009 Pathfinder
P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-261
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
• Harness for open or short between EVAP control system pressure sensor and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-261, "Component Inspection"
OK or NG
OK
>> GO TO 10.
NG
>> Replace EVAP control system pressure sensor.
10.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000004297453
EVAP CONTROL SYSTEM PRESSURE SENSOR
1.
Remove EVAP control system pressure sensor with its harness connector connected from EVAP canister.
Never reuse the O-ring, replace it with a new one.
2.
Install a vacuum pump to EVAP control system pressure sensor.
3.
Turn ignition switch ON and check output voltage between ECM
terminal 32 and ground under the following conditions.
CAUTION:
• Always calibrate the vacuum pump gauge when using it.
• Never apply below -93.3 kPa (-0.952 kg/cm
2
, -13.53 spi) or
pressure over 101.3 kPa (1.033 kg/cm
2
, 14.59 psi).
4.
If NG, replace EVAP control system pressure sensor.
Applied vacuum kPa
(kg/cm
2
, psi)
Voltage V
Not applied
1.8 - 4.8
-26.7 (-0.272, -3.87)
2.1 to 2.5V lower than above value
PBIB1173E
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст