Nissan Pathfinder (2009 year). Instruction — part 576
SEC-30
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2190, P1614 NATS ANTENNA AMP.
B2190, P1614 NATS ANTENNA AMP.
Description
INFOID:0000000003938443
Performs ID verification through BCM and NATS antenna amplifier when ignition knob switch is pressed.
Prohibits the release of steering lock or start of engine when an unregistered ID of mechanical key is used.
DTC Logic
INFOID:0000000003938444
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Insert mechanical key into the key cylinder.
2.
Press the ignition knob switch.
3.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000003938445
1.
CHECK NATS ANTENNA AMP. INSTALLATION
Check NATS antenna amp. installation. Refer to
SEC-118, "Removal and Installation"
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Reinstall NATS antenna amp. correctly.
2.
CHECK NVIS (NATS) IGNITION KEY ID CHIP
Start engine with another registered NATS ignition key.
Does the engine start?
YES
>> • Ignition key ID chip is malfunctioning.
• Replace the ignition key.
• Perform initialization with CONSULT-III.
For initialization, refer to “CONSULT-III Operation Instruction”.
NO
>> GO TO 3
3.
CHECK POWER SUPPLY FOR NATS ANTENNA AMP.
1.
Turn ignition switch ON.
2.
Check voltage between NATS antenna amp. connector M21 terminal 1 and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2190
NATS ANTENNA
AMP
• Inactive communication between NATS antenna
amp. and BCM.
• Mechanical key is malfunctioning.
• Harness or connectors
(The NATS antenna amp. circuit is
open or shorted)
• Mechanical key
• NATS antenna amp.
• BCM
P1614
2009 Pathfinder
B2190, P1614 NATS ANTENNA AMP.
SEC-31
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace fuse or harness.
4.
CHECK NATS ANTENNA AMP. GROUND LINE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect NATS antenna amp. connector.
3.
Check continuity between NATS antenna amp. connector M21 terminal 3 and ground.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> • Repair or replace harness.
NOTE:
If harness is OK, replace BCM, refer to
. Perform initialization with
CONSULT-III. For initialization, refer to “CONSULT-III
Operation Instruction”.
5.
CHECK NATS ANTENNA AMP. SIGNAL LINE- 1
1.
Connect NATS antenna amp. connector.
2.
Turn ignition switch ON.
3.
Check voltage between NATS antenna amp. connector M21 ter-
minal 2 and ground with analog tester.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> • Repair or replace harness.
NOTE:
If harness is OK, replace BCM, refer to
BCS-59, "Removal and Installation"
. Perform initializa-
tion with CONSULT-III. For initialization, refer to “CONSULT-III Operation Instruction”.
1 - Ground
: Battery voltage
LIIA1280E
3 - Ground
: Continuity should exist.
LIIA1283E
LIIA1281E
Terminals
Position of ignition key cylinder
Voltage (V)
(Approx.)
( + )
( - )
2
Ground
Before inserting ignition key
Battery voltage
After inserting ignition key
Pointer of tester should move for approx. 30 seconds,
then return to battery voltage
Just after turning ignition switch
ON
Pointer of tester should move for approx. 1 second, then
return to battery voltage
2009 Pathfinder
SEC-32
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2190, P1614 NATS ANTENNA AMP.
6.
CHECK NATS ANTENNA AMP. SIGNAL LINE- 2
Check voltage between NATS antenna amp. connector M21 terminal
4 and ground with analog tester.
Is the inspection result normal?
YES
>> NATS antenna amp. is malfunctioning.
NO
>> • Repair or replace harness.
NOTE:
If harness is OK, replace BCM, refer to
BCS-59, "Removal and Installation"
. Perform initializa-
tion with CONSULT-III. For initialization, refer to “CONSULT-III Operation Instruction”.
LIIA1282E
Terminals
Position of ignition key cylinder
Voltage (V)
(Approx.)
( + )
( - )
4
Ground
Before inserting ignition key
Battery voltage
After inserting ignition key
Pointer of tester should move for approx. 30 seconds,
then return to battery voltage
Just after turning ignition switch
ON
Pointer of tester should move for approx. 1 second, then
return to battery voltage
2009 Pathfinder
B2191, P1615 DIFFERENCE OF KEY
SEC-33
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2191, P1615 DIFFERENCE OF KEY
Description
INFOID:0000000003938446
Performs ID verification through BCM when ignition knob switch is pressed.
Prohibits the release of steering lock or start of engine when an unregistered ID of mechanical key is used.
DTC Logic
INFOID:0000000003938447
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Insert mechanical key into the key cylinder.
2.
Press the ignition knob switch.
3.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000003938448
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to “CONSULT-III Operation Instruction”.
Can the system be initialized and can the engine be started with re-registered mechanical key?
YES
>> Mechanical key was unregistered.
NO
>>
BCM is malfunctioning.
• Replace BCM. Refer to
BCS-59, "Removal and Installation"
.
• Perform initialization again.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2191
DIFFERENCE OF
KEY
The ID verification results between BCM and me-
chanical key are NG. The registration is necessary.
Mechanical key
P1615
2009 Pathfinder
SEC-34
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2192, P1611 ID DISCORD, IMMU-ECM
B2192, P1611 ID DISCORD, IMMU-ECM
Description
INFOID:0000000003938449
BCM performs the ID verification with ECM that allows the engine to start. BCM starts the communication with
ECM if ignition switch is turned ON and starts the engine if the ID is OK. ECM prevents the engine from start-
ing if the ID is not registered.
DTC Logic
INFOID:0000000003938450
DTC DETECTION LOGIC
NOTE:
• If DTC B2192 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2192 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000003938451
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to “CONSULT-III Operation Instruction”.
Can the system be initialized and can the engine be started with re-registered mechanical key?
YES
>> ID was unregistered.
NO
>> GO TO 2
2.
PEPLACE BCM
1.
Replace BCM. Refer to
BCS-59, "Removal and Installation"
.
2.
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to “CONSULT-III Operation Instruction”.
Can the system be initialized and can the engine be started with re-registered mechanical key?
YES
>> BCM is malfunctioning.
NO
>> GO TO 3
3.
PEPLACE ECM
1.
Replace ECM. Refer to Removal and Installation.
2.
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to “CONSULT-III Operation Instruction”.
Can the system be initialized and can the engine be started with re-registered mechanical key?
YES
>> ECM is malfunctioning.
NO
>> GO TO 4
4.
CHECK INTERMITENT INCIDENT
GI-49, "Intermittent Incident"
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2192
ID DISCORD BCM-
ECM
The ID verification results between BCM and ECM
are NG. The registration is necessary.
• BCM
• ECM
P1611
2009 Pathfinder
B2192, P1611 ID DISCORD, IMMU-ECM
SEC-35
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
>> Inspection End.
2009 Pathfinder
SEC-36
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2193, P1612 CHAIN OF ECM-IMMU
B2193, P1612 CHAIN OF ECM-IMMU
Description
INFOID:0000000003938452
BCM performs the ID verification with ECM that allows the engine to start. BCM starts the communication with
ECM if ignition switch is turned ON and starts the engine if the ID is OK. ECM prevents the engine from start-
ing if the ID is not registered.
DTC Logic
INFOID:0000000003938453
DTC DETECTION LOGIC
NOTE:
• If DTC B2193 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2193 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000003938454
1.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-59, "Removal and Installation"
.
2.
Perform initialization with CONSULT-III.
For initialization, refer to “CONSULT-III Operation Instruction”.
Does the engine start?
YES
>> BCM was malfunctioning.
NO
>>
ECM is malfunctioning.
• Replace ECM.
• Perform ECM re-communicating function.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2193
CHAIN OF BCM-
ECM
Inactive communication between ECM and BCM
• Harness or connectors
(The CAN communication line is
open or short)
• BCM
• ECM
P1612
2009 Pathfinder
B2194 ID DISCORD IMMU-I-KEY
SEC-37
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2194 ID DISCORD IMMU-I-KEY
Description
INFOID:0000000003938455
BCM performs the ID verification with Intelligent Key unit that allows the engine to start. BCM starts the com-
munication with Intelligent Key unit if ignition switch is turned ON and starts the engine if the ID is OK. BCM
prevents the engine from starting if the ID is not registered.
DTC Logic
INFOID:0000000003938456
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000003938457
1.
PERFORM INITIALIZATION
1.
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to “CONSULT-III Operation Instruction”.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> GO TO 2
NO
>> ID was unregistered.
2.
REPLACE BCM
1.
Turn ignition switch OFF.
2.
Replace BCM. Refer to
BCS-59, "Removal and Installation"
.
3.
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to “CONSULT-III Operation Instruction”.
Can the system be initialized and can the engine be started?
YES
>> BCM is malfunctioning.
NO
>> GO TO 3
3.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
>> Inspection End.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2194
DISCORD BCM-I-
KEY
The ID verification results between BCM and Intel-
ligent Key unit are NG. The registration is neces-
sary.
• BCM
• Intelligent Key unit
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст