Nissan Pathfinder (2009 year). Instruction — part 292
EC-350
< COMPONENT DIAGNOSIS >
[VQ40DE]
P1800 VIAS CONTROL SOLENOID VALVE 1
4.
Check air passage continuity and operation delay time under the
following conditions.
Operation takes less than 1 second.
With GST
Check air passage continuity and operation delay time under the fol-
lowing conditions.
Operation takes less than 1 second.
Condition
VIAS SOL VALVE
Air passage continuity
between (A) and (B)
Air passage continuity
between (A) and (C)
ON
Yes
No
OFF
No
Yes
JMBIA0180ZZ
Condition
Air passage continuity
between (A) and (B)
Air passage continuity
between (A) and (C)
12V direct current supply
between terminals 1 and 2
Yes
No
No supply
No
Yes
PBIB2532E
2009 Pathfinder
P1805 BRAKE SWITCH
EC-351
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1805 BRAKE SWITCH
Description
INFOID:0000000004297581
Brake switch signal is applied to the ECM through the stop lamp switch when the brake pedal is depressed.
This signal is used mainly to decrease the engine speed when the vehicle is being driven.
On Board Diagnosis Logic
INFOID:0000000004297582
The MIL will not illuminate for this diagnosis.
FAIL-SAFE MODE
When the malfunction is detected, the ECM enters fail-safe mode.
DTC Confirmation Procedure
INFOID:0000000004297583
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
1.
Turn ignition switch ON.
2.
Fully depress the brake pedal for at least 5 seconds.
3.
Erase the DTC with CONSULT-III.
4.
Check 1st trip DTC.
5.
If 1st trip DTC is detected, go to
Diagnosis Procedure
INFOID:0000000004297584
1.
CHECK STOP LAMP SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Check the stop lamp when depressing and releasing the brake pedal.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 2.
2.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1805
1805
Brake switch
A brake switch signal is not sent to ECM for ex-
tremely long time while the vehicle is being driv-
en.
• Harness or connectors
(Stop lamp switch circuit is open or short-
ed.)
• Stop lamp switch
Engine operating condition in fail-safe mode
ECM controls the electric throttle control actuator by regulating the throttle opening to a small range.
Therefore, acceleration will be poor.
Vehicle condition
Driving condition
When engine is idling
Normal
When accelerating
Poor acceleration
Brake pedal
Stop lamp
Fully released
Not illuminated
Slightly depressed
Illuminated
2009 Pathfinder
EC-352
< COMPONENT DIAGNOSIS >
[VQ40DE]
P1805 BRAKE SWITCH
1.
Disconnect stop lamp switch harness connector.
2.
Check voltage between stop lamp switch terminal 1 and ground
with CONSULT-III or tester.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Check the following.
• 10A fuse
• Fuse block (J/B) connector E160
• Harness for open and short between stop lamp switch and battery
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connector.
2.
Disconnect stop lamp switch harness connector.
3.
Check harness continuity between ECM terminal 101 and stop
lamp switch terminal 2.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
5.
CHECK STOP LAMP SWITCH
EC-353, "Component Inspection"
OK or NG
OK
>> GO TO 6.
NG
>> Replace stop lamp switch.
6.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
>> INSPECTION END
BBIA0560E
Voltage: Battery voltage
PBIB1184E
Continuity should exist.
BBIA0560E
2009 Pathfinder
P1805 BRAKE SWITCH
EC-353
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Component Inspection
INFOID:0000000004297585
STOP LAMP SWITCH
1.
Disconnect stop lamp switch harness connector.
2.
Check continuity between stop lamp switch terminals 1 and 2
under the following conditions.
3.
If NG, adjust stop lamp switch installation, refer to
"Inspection and Adjustment - Standard Pedal"
or
"Inspection and Adjustment - Adjustable Pedal"
, and perform
step 2 again.
BBIA0560E
Conditions
Continuity
Brake pedal: Fully released
Should not exist.
Brake pedal: Slightly depressed
Should exist.
PBIB1185E
2009 Pathfinder
EC-354
< COMPONENT DIAGNOSIS >
[VQ40DE]
P2100, P2103 THROTTLE CONTROL MOTOR RELAY
P2100, P2103 THROTTLE CONTROL MOTOR RELAY
Component Description
INFOID:0000000004297586
Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle
control motor relay is controlled ON/OFF by the ECM. When the ignition switch is turned ON, the ECM sends
an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition
switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not
provided to the ECM.
On Board Diagnosis Logic
INFOID:0000000004297587
These self-diagnoses have the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, ECM enters fail-safe mode and the MlL illuminate.
DTC Confirmation Procedure
INFOID:0000000004297588
NOTE:
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next step.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
PROCEDURE FOR DTC P2100
1.
Turn ignition switch ON and wait at least 2 seconds.
2.
Start engine and let it idle for 5 seconds.
3.
Check 1st trip DTC.
4.
If DTC is detected, go to
.
PROCEDURE FOR DTC P2103
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8V.
1.
Turn ignition switch ON and wait at least 1 second.
2.
Check DTC.
3.
If DTC is detected, go to
.
Diagnosis Procedure
INFOID:0000000004297589
1.
CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT-I
1.
Turn ignition switch OFF.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2100
2100
Throttle control motor
relay circuit open
ECM detects that the voltage of power source
for throttle control motor is excessively low.
• Harness or connectors
(Throttle control motor relay circuit is
open)
• Throttle control motor relay
P2103
2103
Throttle control motor
relay circuit short
ECM detects that the throttle control motor relay
is stuck ON.
• Harness or connectors
(Throttle control motor relay circuit is
shorted)
• Throttle control motor relay
Engine operating condition in fail-safe mode
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return
spring.
2009 Pathfinder
P2100, P2103 THROTTLE CONTROL MOTOR RELAY
EC-355
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
Check voltage between ECM terminal 104 and ground with
CONSULT-III or tester.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 2.
2.
CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT-II
1.
Disconnect ECM harness connector.
2.
Disconnect IPDM E/R harness connector E122.
3.
Check continuity between ECM terminal 104 and IPDM E/R terminal 47.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
3.
CHECK FUSE
1.
Disconnect 20 A fuse (No.52).
2.
Check if 20A fuse is blown.
OK or NG
OK
>> GO TO 7.
NG
>> Replace 20A fuse.
4.
CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-I
1.
Check voltage between ECM terminal 3 and ground under the
following conditions with CONSULT-III or tester.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 5.
5.
CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Disconnect IPDM E/R harness connector E119.
4.
Check continuity between ECM terminal 3 and IPDM E/R terminal 6.
Refer to Wiring Diagram.
5.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
Voltage: Battery voltage
PBIB1171E
Continuity should exist.
Ignition switch
Voltage
OFF
Approximately 0V
ON
Battery voltage
(11 - 14V)
MBIB0028E
Continuity should exist.
2009 Pathfinder
EC-356
< COMPONENT DIAGNOSIS >
[VQ40DE]
P2100, P2103 THROTTLE CONTROL MOTOR RELAY
6.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E2, F32
• Harness for open or short between ECM and IPDM E/R
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
OK or NG
OK
>> Replace IPDM E/R. Refer to
PCS-33, "Removal and Installation of IPDM E/R"
.
NG
>> Repair or replace harness or connectors.
2009 Pathfinder
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
EC-357
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
Description
INFOID:0000000004297590
NOTE:
If DTC P2101 is displayed with DTC P2100 or P2119, first perform the trouble diagnosis for DTC P2100
or P2119. Refer to
Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc.
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor. The throttle position
sensor provides feedback to the ECM, when opens/closes the throttle valve in response to driving conditions
via the throttle control motor.
On Board Diagnosis Logic
INFOID:0000000004297591
This self-diagnosis has the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, ECM enters fail-safe mode and the MIL illuminates.
DTC Confirmation Procedure
INFOID:0000000004297592
NOTE:
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next step.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11V when the
engine is running.
1.
Turn ignition switch ON and wait at least 2 seconds.
2.
Start engine and let it idle for 5 seconds.
3.
Check DTC.
4.
If DTC is detected, go to
.
Diagnosis Procedure
INFOID:0000000004297593
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2101
2101
Electric throttle control
performance
Electric throttle control function does not oper-
ate properly.
• Harness or connectors
(Throttle control motor circuit is open or
shorted)
• Electric throttle control actuator
Engine operating condition in fail-safe mode
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return
spring.
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст