Nissan Pathfinder (2009 year). Instruction — part 561
PREPARATION
RF-51
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000003938834
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000003938835
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis ear
Locating the noise
—
(J-43980)
NISSAN Squeak and
Rattle Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear
Locating the noise
SIIA0995E
2009 Pathfinder
RF-52
< ON-VEHICLE REPAIR >
SUNROOF SYSTEM
ON-VEHICLE REPAIR
SUNROOF SYSTEM
Adjustment
INFOID:0000000003938836
Inspect then measure the gap and height difference between the glass lid assembly and roof panel; compare
to specifications. Determine which procedure to follow based on results of measurements.
GAP ADJUSTMENT
If a gap or minor height difference between glass lid assembly and roof panel is found, adjust in the following
manner:
1.
Open sunshade assembly and tilt glass lid assembly up.
2.
Loosen glass lid assembly screws (2 each on left and right sides), then tilt glass lid assembly down.
3.
Instructionly adjust glass lid assembly from outside of vehicle so it is within specification "A-A" as shown.
4.
After adjustment, tilt glass lid assembly up and tighten screws.
5.
Tilt glass lid assembly up and down several times to check that it moves and seals properly.
HEIGHT DIFFERENCE ADJUSTMENT
If an excessive height difference between glass lid assembly and roof panel is found, adjust in the following
manner:
1.
Remove headlining. Refer to
INT-20, "Removal and Installation"
2.
Loosen sunroof frame assembly nuts and sunroof bracket bolts.
3.
Add shims until gap is within specification "A-A" as shown.
NOTE:
Temporarily snug nuts and bolts to prevent movement between each adjustment.
4.
Tilt glass lid assembly up and down several times to check that it moves and seals properly.
5.
Tighten sunroof frame assembly nuts and sunroof bracket bolts.
NOTE:
A.
0.8
±
1.5mm (0.03
±
0.06 in.)
B.
4.0
±
0.7mm (0.16
±
0.03 in)
WIIA1071E
2009 Pathfinder
SUNROOF SYSTEM
RF-53
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
First tighten left front then right rear sunroof frame assembly nuts to prevent uneven torque while tighten-
ing remaining sunroof bracket bolts.
6.
Install headlining. Refer to
INT-20, "Removal and Installation"
.
Removal and Installation
INFOID:0000000003938837
WIIA0423E
2009 Pathfinder
RF-54
< ON-VEHICLE REPAIR >
SUNROOF SYSTEM
• After any adjustment, check sunroof operation and glass lid alignment.
• Handle glass lid with care so not to cause damage.
• For easier installation, mark each point before removal.
CAUTION:
• Always work with a helper.
• Before removal, fully close the glass lid assembly. Then, after removal, do not move the motor
assembly.
• After installing the sunroof and glass lid, check gap adjustment to ensure there is no malfunction.
SUNROOF UNIT
Removal
CAUTION:
• Always work with a helper.
• When taking sunroof unit out, use shop cloths to protect the seats and trim from damage.
• After installing the sunroof unit and glass lid, be sure to check gap adjustment to ensure there is no
malfunction.
1.
Remove headlining. Refer to
INT-20, "Removal and Installation"
2.
Remove the sunroof glass lid.
3.
Disconnect sunroof motor and remove the overhead console bracket.
4.
Disconnect the drain hoses.
5.
Remove front sunroof frame assembly nuts.
6.
Remove the rear sunroof bracket bolts.
7.
Remove the side bolts and the sunroof unit.
Installation
1.
Position the sunroof frame assembly and install the side bolts.
2.
Install the rear sunroof bracket bolts.
3.
Install front sunroof frame assembly nuts.
4.
Connect the drain hoses.
5.
Install the overhead console bracket and connect the sunroof motor.
6.
Install the sunroof glass lid.
7.
Install headlining. Refer to
INT-20, "Removal and Installation"
.
GLASS LID
Removal
1.
Open sunshade.
2.
Ensure glass lid is closed.
3.
Remove the screws securing glass lid to the sunroof frame assembly.
4.
Remove the glass lid assembly.
Installation
1.
Position glass lid to sunroof assembly.
1.
Glass lid assembly
2.
Wind deflector
3.
Rear drain hoses
4.
Shade stoppers
5.
Sunroof bracket
6.
Sunroof frame assembly
7.
Front drain hoses
8.
Sunroof motor assembly
9.
Sunshade assembly
2009 Pathfinder
SUNROOF SYSTEM
RF-55
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
2.
Install the glass lid assembly screws. (First tighten left front bolt,
then tighten right rear bolt on glass lid to prevent lid from moving
while tightening other bolts.)
3.
Adjust the sunroof glass. Refer to
.
WIND DEFLECTOR
Removal
1.
Open the sunroof.
2.
Remove screws from the left, center, and right side wind deflec-
tor holders.
3.
Remove the wind deflector from the sunroof frame assembly.
Installation
Installation is in the reverse order of removal.
SUNSHADE
Removal
1.
Remove the sunroof frame assembly. Refer to
RF-53, "Removal and Installation"
.
2.
Remove the sunshade stoppers (2 points) from the rear end of
the sunroof frame assembly.
3.
Remove the sunshade assembly from the rear end of the sun-
roof frame assembly.
Installation
Installation is in the reverse order of removal.
SUNROOF MOTOR
Removal
CAUTION:
• When removing the sunroof motor, be sure that the sunroof is in the fully closed position.
• Never run the removed motor as a single unit.
1.
Position the sunroof assembly in the fully closed position.
2.
Remove the front roof console assembly. Refer to
INT-20, "Removal and Installation"
.
WIIA0252E
WIIA0424E
LIIA1672E
2009 Pathfinder
RF-56
< ON-VEHICLE REPAIR >
SUNROOF SYSTEM
3.
Disconnect the harness connector from the sunroof motor
assembly.
4.
Remove the mounting screws and the sunroof motor assembly.
Installation
CAUTION:
Before installing the sunroof motor assembly, be sure to place the link and wire assembly in the sym-
metrical and fully closed position.
1.
Move the sunroof motor assembly laterally little by little so that
the gear is completely engaged into the wire on the sunroof unit
and the mounting surface becomes parallel. Then secure the
motor with bolts.
2.
Connect the harness connector to the sunroof motor assembly.
3.
Install the front roof console assembly. Refer to
INT-20, "Removal and Installation"
4.
Reset the sunroof motor memory. Refer to
RF-5, "ADDITIONAL SERVICE WHEN REPLACING CON-
TROL UNIT : Special Repair Requirement"
DRAIN HOSES
Removal
LIIA1673E
LIIA1674E
1.
Drain hoses
WIIA1072E
2009 Pathfinder
SUNROOF SYSTEM
RF-57
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
1.
Remove the headlining. Refer to
INT-20, "Removal and Installation"
.
2.
Visually check the drain hoses for proper connections, damage or deterioration.
3.
Remove each drain hose and check visually for damage, cracks or deterioration.
4.
Pour water through the drain hose to check for damage.
• If any damage is found, replace the drain hose.
Installation
Installation is in the reverse order of removal.
WEATHERSTRIP
Visually check weatherstrip for any damage, deterioration, or flattening.
• In the case of leakage around glass lid, close glass lid and pour water around it to find the damaged or
gaped portion, remove glass lid assembly. Refer to:
RF-53, "Removal and Installation"
.
• If any damage is found, replace glass lid assembly. Refer to:
RF-53, "Removal and Installation"
.
CAUTION:
Do not remove weatherstrip.
LINK AND WIRE ASSEMBLY
NOTE:
Before replacing any suspect part, be sure it is the source of the noise.
1.
Visually check to determine if a sufficient amount of petroleum jelly has been applied to the wire or rail
groove. If not, add petroleum jelly as required.
2.
Check wire for any damage or deterioration. If any damage is found, remove rear guide, then replace
wire.
LIIA0272E
2009 Pathfinder
RSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
RSU
A
B
RSU
N
O
P
CONTENTS
REAR SUSPENSION
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
Precaution for Rear Suspension . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION, AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
ON-VEHICLE MAINTENANCE . . . . . .
REAR SUSPENSION ASSEMBLY . . . . . .
On-Vehicle Inspection . . . . . . . . . . . ...
Wheel Alignment Inspection . . . . . . . . . ..
SHOCK ABSORBER . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
ON-VEHICLE REPAIR . . . . . . . . .
REAR SUSPENSION ASSEMBLY . . . . ...
Component . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
REAR SUSPENSION MEMBER . . . . . ...
Removal and Installation . . . . . . . . . . .
SHOCK ABSORBER . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SUSPENSION ARM . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . .
FRONT LOWER LINK . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
REAR LOWER LINK & COIL SPRING . . . .
Removal and Installation . . . . . . . . . . .
STABILIZER BAR . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Alignment . . . . . . . . . . . . . .
Ball Joint . . . . . . . . . . . . . . . . ..
Wheelarch Height (Unladen*) . . . . . . . . ..
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст