Nissan Pathfinder (2009 year). Instruction — part 85
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Hazard and horn reminder mode
Auto locking function mode
Panic alarm operation mode
Back door open operation mode
Keyless power window down operation mode
DATA MONITOR
ACTIVE TEST
MODE 1
(C mode)
MODE 2
(S mode)
MODE 3
MODE 4
MODE 5
MODE 6
Keyfob
operation
Lock
Unlock
Lock
Unlock
Lock
Unlock
Lock
Unlock
Lock
Unlock
Lock
Unlock
Hazard warning
lamp flash
Twice
Once
Twice
—
—
—
Twice
Once
Twice
—
—
Once
Horn sound
Once
—
—
—
—
—
—
—
Once
—
Once
—
MODE 1
MODE 2
MODE 3
Auto locking function
5 minutes
Nothing
1 minute
MODE 1
MODE 2
MODE 3
Keyfob operation
0.5 seconds
Nothing
1.5 seconds
MODE 1
MODE 2
MODE 3
Keyfob operation
0.5 seconds
Nothing
0.5 seconds
MODE 1
MODE 2
MODE 3
Keyfob operation
3 seconds
Nothing
5 seconds
Monitored Item
Description
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch in ACC position.
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
KEYLESS PANIC
Indicates [ON/OFF] condition of panic signal from keyfob.
KEYLESS UNLOCK
Indicates [ON/OFF] condition of unlock signal from keyfob.
KEYLESS LOCK
Indicates [ON/OFF] condition of lock signal from keyfob.
KEY CYL LK-SW
Indicates [ON/OFF] condition of lock signal from door key cylinder switch.
KEY CYL UN-SW
Indicates [ON/OFF] condition of unlock signal from door key cylinder switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from lock/unlock switch.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from lock/unlock switch.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
RKE LCK-UNLCK
Indicates [ON/OFF] condition of lock/unlock signal at the same time from keyfob.
RKE KEEP UNLK
Indicates [ON/OFF] condition of unlock signal from keyfob.
2009 Pathfinder
BCS-22
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000003935263
WORK SUPPORT
*: Initial setting
DATA MONITOR
Test Item
Description
FLASHER
This test is able to check right and left hazard reminder operation. The right hazard lamp turns on
when “RH” on CONSULT-III screen is touched and the left hazard lamp turns on when "LH" on CON-
SULT-III screen is touched.
POWER WINDOW DOWN
This test is able to check power window down operation. The windows are lowered when “ON” on
CONSULT-III screen is touched.
HORN
This test is able to check panic alarm and horn reminder operations. The alarm activate for 0.5 sec-
onds after “ON” on CONSULT-III screen is touched.
DOOR LOCK
This test is able to check door lock operation. The doors lock and unlock based on the item on CON-
SULT-III screen touched.
Work Item
Setting item
Setting
BATTERY SAVER SET
ON*
With the exterior lamp battery saver function
OFF
Without the exterior lamp battery saver function
CUSTOM A/LIGHT SET-
TING
MODE1*
Normal
MODE2
More sensitive setting than normal setting (Turns ON earlier than normal operation.)
MODE3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE4
Less sensitive setting than normal setting (Turns ON later than normal operation.)
ILL DELAY SET
MODE1*
45 sec.
Sets delay timer function timer operation time
(All doors closed)
MODE2
Without the func-
tion
MODE3
30 sec.
MODE4
60 sec.
MODE5
90 sec.
MODE6
120 sec.
MODE7
150 sec.
MODE8
180 sec.
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
ACC ON SW [ON/OFF]
Ignition switch (ACC) status judged from ACC signal (accessory power supply)
2009 Pathfinder
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-23
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: The item is indicated, not monitored.
ACTIVE TEST
*: The item is indicated, not monitored.
WIPER
WIPER : CONSULT-III Function (BCM - WIPER)
INFOID:0000000003935264
WORK SUPPORT
HI BEAM SW [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW 1 [ON/OFF]
HEAD LAMP SW 2 [ON/OFF]
LIGHT SW 1ST [ON/OFF]
AUTO LIGHT SW [ON/OFF]
PASSING SW [ON/OFF]
FR FOG SW [ON/OFF]
RR FOG SW [ON/OFF]*
TURN SIGNAL R [ON/OFF]
TURN SIGNAL L [ON/OFF]
DOOR SW-DR [ON/OFF]
The switch status input from front door switch LH
DOOR SW-AS [ON/OFF]
The switch status input from front door switch RH
DOOR SW-RR [ON/OFF]
The switch status input from rear door switch RH
DOOR SW-RL [ON/OFF]
The switch status input from rear door switch LH
BACK DOOR SW [ON/OFF]
The switch status input from back door switch
CARGO LAMP SW [ON/OFF]
Cargo lamp status that BCM judges from the vehicle condition
OPTICAL SENSOR [ON/OFF]
The value of exterior brightness voltage input from the optical sensor
Monitor Item
[Unit]
Description
Test Item
Operation
Description
TAIL LAMP
ON
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
OFF
Stops the tail lamp request signal transmission.
HEAD LAMP
HI
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LO
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
OFF
Stops the high & low beam request signal transmission.
FR FOG LAMP
ON
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
OFF
Stops the front fog lights request signal transmission.
CARGO LAMP
ON
Transmits the cargo lamp request signal to IPDM E/R with CAN commu-
nication to turn the each lamp ON.
OFF
Stops the day time running light request signal transmission.
CORNERING LAMP*
RH
—
LH
OFF
2009 Pathfinder
BCS-24
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
*: Factory setting
DATA MONITOR
*: The item is indicated, not monitored.
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000003935265
DATA MONITOR
Work Item
Setting
Item
Description
WIPER SPEED
SETTING
ON*
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
OFF
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch ON status judged from ignition power supply
IGN SW CAN [ON/OFF]
Ignition switch ON status received from IPDM E/R with CAN communication
FR WIPER HI [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
FR WIPER LOW [ON/OFF]
FR WIPER INT [ON/OFF]
FR WASHER SW [ON/OFF]
INT VOLUME [1 - 7]
Each switch status that BCM judges from the combination switch reading function
FR WIPER STOP [ON/OFF]
Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
tion
VEHICLE SPEED [km/h]
The value of the vehicle speed signal received from combination meter with CAN com-
munication
RR WIPER ON [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
RR WIPER INT [ON/OFF]
RR WASHER SW [ON/OFF]
RR WIPER STOP [ON/OFF]
Rear wiper motor (stop position) status input from the rear wiper motor
H/L WASH SW*
—
Test Item
Operation
Description
FR WIPER
HI
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.
LO
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
OFF
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
ON
Outputs the voltage to operate the rear wiper motor.
OFF
Stops the voltage to stop.
2009 Pathfinder
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-25
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
AIR CONDITIONER
AIR CONDITIONER : CONSULT-III Function (BCM - AIR CONDITIONER)
INFOID:0000000003935266
DATA MONITOR
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)
INFOID:0000000003935267
DATA MONITOR
COMB SW
COMB SW : CONSULT-III Function (BCM - COMB SW)
INFOID:0000000003935268
DATA MONITOR
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
HAZARD SW [ON/OFF]
The switch status input from the hazard switch
TURN SIGNAL R [ON/OFF]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L [ON/OFF]
BRAKE SW [ON/OFF]
The switch status input from the brake switch
Test Item
Operation
Description
FLASHER
RH
Outputs the voltage to turn the right side turn signal lamps ON.
LH
Outputs the voltage to turn the left side turn signal lamps ON.
OFF
Stops the voltage to turn the turn signal lamps OFF.
Monitor Item
[Unit]
Contents
IGN ON SW [ON/OFF]
Display [ignition switch position (On)/(Off), ACC position (Off)] status as judged from ignition
switch signal
FAN ON SIG [ON/OFF]
Display [FAN (On)/FAN (Off)] status as judged form blower fan motor switch signal
AIR COND SW [ON/OFF]
Display [COMP (On)/COMP (Off)] status as judged form air conditioner switch signal
Monitor Item
[Unit]
Condition
I-KEY LOCK [ON/OFF]
Indicates condition of lock signal from Intelligent Key
I-KEY UNLOCK [ON/OFF]
Indicates condition of unlock signal from Intelligent Key
I-KEY PW DWN [ON/OFF]
Indicates condition of all power window signal from Intelligent Key
I-KEY TRUNK [ON/OFF]
Indicates condition of trunk open signal from Intelligent Key
I-KEY PANIC [ON/OFF]
Indicates condition of panic signal from Intelligent Key
PUSH SW [ON/OFF]
Indicates condition of ignition knob switch
2009 Pathfinder
BCS-26
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
*: The item is indicated, not monitored.
IMMU
IMMU : CONSULT-III Function (BCM - IMMU)
INFOID:0000000003935269
DATA MONITOR
ACTIVE TEST
Monitor Item
[Unit]
Description
TURN SIGNAL R
[OFF/ON]
Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function
TURN SIGNAL L
[OFF/ON]
Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
reading function
HI BEAM SW
[OFF/ON]
Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
reading function
HEADLAMP SW1
[OFF/ON]
Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function
HEADLAMP SW2
[OFF/ON]
Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function
LIGHT SW 1ST
[OFF/ON]
Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function
PASSING SW
[OFF/ON]
Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
reading function
AUTO LIGHT SW
[OFF/ON]
Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function
FR FOG SW
[OFF/ON]
Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function
RR FOG SW*
[OFF/ON]
—
FR WIPER HI
[OFF/ON]
Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function
FR WIPER LOW
[OFF/ON]
Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function
FR WIPER INT
[OFF/ON]
Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function
FR WASHER SW
[OFF/ON]
Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function
INT VOLUME
[1 - 7]
Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading
function
RR WIPER ON
[OFF/ON]
Displays the status of the RR WIPER switch in combination switch judged by BCM with the combination
switch reading function
RR WIPER INT
[OFF/ON]
Displays the status of the RR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function
RR WASHER SW
[OFF/ON]
Displays the status of the RR WASHER switch in combination switch judged by BCM with the combination
switch reading function
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Indicates condition of ignition switch in ON position.
Test Item
Description
THEFT IND
This test is able to check security indicator operation [ON/OFF].
2009 Pathfinder
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-27
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)
INFOID:0000000003935270
WORK SUPPORT
*: Initial setting
DATA MONITOR
1: With Intelligent Key
2: With remote keyless entry
ACTIVE TEST
*: Each lamp switch is in ON position.
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)
INFOID:0000000003935271
DATA MONITOR
Work Item
Setting Item
Setting
ROOM LAMP TIMER SET
MODE 1*
15 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
30 min.
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judges from IGN signal (ignition power supply)
KEY ON SW [ON/OFF]
The switch status input from key switch
DOOR SW-DR [ON/OFF]
The switch status input from front door switch (driver side)
DOOR SW-AS [ON/OFF]
The switch status input from front door switch (passenger side)
DOOR SW-RR [ON/OFF]
The switch status input from rear door switch RH
DOOR SW- RL [ON/OFF]
The switch status input from rear door switch LH
BACK DOOR SW [ON/OFF]
The switch status input from back door switch
KEY CYL LK-SW [ON/OFF]
Lock switch status input from door key cylinder switch
KEY CYL UN-SW [ON/OFF]
Unlock switch status input from door key cylinder switch
CDL LOCK SW [ON/OFF]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW [ON/OFF]
Unlock switch status input from door lock and unlock switch
I-KEY LOCK
1
[ON/OFF]
Lock signal status received from Intelligent Key unit by CAN communication
I-KEY UNLOCK
1
[ON/OFF]
Unlock signal status received from Intelligent Key unit by CAN communication
KEYLESS LOCK
2
[ON/OFF]
Lock signal status received from remote keyless entry receiver (integrated in the
BCM)
KEYLESS UNLOCK
2
[ON/OFF]
Unlock signal status received from remote keyless entry receiver (integrated in the
BCM)
Test Item
Operation
Description
BATTERY SAVER
OFF
Cuts the interior room lamp power supply to turn interior room lamps OFF.
ON
Outputs the interior room lamp power supply to turn interior room lamps ON.*
Monitor Item
[Unit]
Contents
IGN ON SW [ON/OFF]
Indicates condition of ignition switch in ON position
I-KEY TRUNK [ON/OFF]
Indicates condition of Intelligent Key back door opening operation
2009 Pathfinder
BCS-28
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
RETAINED PWR
RETAINED PWR : CONSULT-III Function (BCM - RETAINED PWR)
INFOID:0000000003935272
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER)
INFOID:0000000003935273
DATA MONITOR
ACTIVE TEST
TRUNK OPNR SW [ON/OFF]
Indicates condition of back door opener switch.
VEHICLE SPEED [ON/OFF]
Indicates condition of vehicle speed signal from combination meter
Monitor Item
[Unit]
Contents
Test Item
Description
TRUNK/BACK DOOR
This test is able to check back door open operation.
Back door open when “OPEN” on CONSULT-III screen is touched.
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Indicates condition of ignition switch.
DOOR SW-DR [ON/OFF]
Indicates condition of front door switch LH.
DOOR SW-AS [ON/OFF]
Indicates condition of front door switch RH.
Test Item
Description
RETAINED PWR
This test is able to supply RAP signal (power) from BCM (body control module) to power window
system and power sunroof system (if equipped). Those systems can be operated when turning on
“RETAINED PWR” on CONSULT-III screen even if the ignition switch is turned OFF.
NOTE:
During this test, CONSULT-III can be operated with ignition switch in OFF position. “RETAINED
PWR” should be turned “ON” or “OFF” on CONSULT-III screen when ignition switch is ON. Then
turn ignition switch OFF to check retained power operation. CONSULT-III might be stuck if “RE-
TAINED PWR” is turned “ON” or “OFF” on CONSULT-III screen when ignition switch is OFF.
Work item
Description
RETAINED PWR SET
RAP signal’s power supply period can be changed by mode setting. Selects RAP signal’s power
supply period between three steps
• MODE1 (45 sec.)/MODE2 (OFF)/MODE 3 (2 min.).
Monitor Item
[Unit]
Description
OIL PRESS SW [ON/OFF]
Displays the status of oil pressure switch received from IPDM E/R via CAN communication.
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст