Nissan Pathfinder (2009 year). Instruction — part 338
EC-718
< COMPONENT DIAGNOSIS >
[VK56DE]
P0444, P0445 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID
VALVE
4.
Also check harness for short to ground and short to power.
OK or NG
OK (With CONSULT-III)>>GO TO 4.
OK (Without CONSULT-III)>>GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
With CONSULT-III
1.
Reconnect all harness connectors disconnected.
2.
Start engine.
3.
Perform “PURG VOL CONT/V” in “ACTIVE TEST” mode with CONSULT-III. Check that engine speed var-
ies according to the valve opening.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
5.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-718, "Component Inspection"
OK or NG
OK
>> GO TO 6.
NG
>> Replace EVAP canister purge volume control solenoid valve.
6.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000003936649
EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
With CONSULT- III
Check air passage continuity of EVAP canister purge volume control
solenoid valve under the following conditions.
Without CONSULT-III
Check air passage continuity of EVAP canister purge volume control
solenoid valve under the following conditions.
Condition
(PURG VOL C/V value)
Air passage continuity
between A and B
100%
Yes
0%
No
PBIB2058E
Condition
Air passage continuity
between A and B
12V direct current supply between
terminals 1 and 2
Yes
No supply
No
PBIB2059E
2009 Pathfinder
P0447 EVAP CANISTER VENT CONTROL VALVE
EC-719
< COMPONENT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0447 EVAP CANISTER VENT CONTROL VALVE
Component Description
INFOID:0000000003936650
The EVAP canister vent control valve (3) is located on the EVAP
canister (4) and is used to seal the canister vent.
• Fuel filler pipe (top of frame view) (1)
• EVAP control system pressure sensor (2)
• Drain filter (5)
•
: Vehicle front
This solenoid valve responds to signals from the ECM. When the
ECM sends an ON signal, the coil in the solenoid valve is energized.
A plunger will then move to seal the canister vent. The ability to seal
the vent is necessary for the on board diagnosis of other evaporative
emission control system components.
This solenoid valve is used only for diagnosis, and usually remains
opened.
When the vent is closed, under normal purge conditions, the evapo-
rative emission control system is depressurized and allows “EVAP
Control System” diagnosis.
On Board Diagnosis Logic
INFOID:0000000003936651
DTC Confirmation Procedure
INFOID:0000000003936652
NOTE:
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next step.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm battery voltage is more than 11 V at idle.
1.
Start engine and wait at least 8 seconds.
2.
Check 1st trip DTC.
3.
If 1st trip DTC is detected, go to
Diagnosis Procedure
INFOID:0000000003936653
1.
INSPECTION START
Will CONSULT-III be used?
Yes or No
Yes
>> GO TO 2.
No
>> GO TO 3.
AWBIA0134ZZ
PBIB3642E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0447
0447
EVAP canister vent control
valve circuit open
An improper voltage signal is sent to ECM
through EVAP canister vent control valve.
• Harness or connectors
(The valve circuit is open or shorted.)
• EVAP canister vent control valve
• Drain filter
2009 Pathfinder
EC-720
< COMPONENT DIAGNOSIS >
[VK56DE]
P0447 EVAP CANISTER VENT CONTROL VALVE
2.
CHECK EVAP CANISTER VENT CONTROL VALVE CIRCUIT
With CONSULT-III
1.
Turn ignition switch OFF and then ON.
2.
Select “VENT CONTROL/V” in “ACTIVE TEST” mode with CONSULT-III.
3.
Touch “ON/OFF” on CONSULT-III screen.
4.
Check for operating sound of the valve.
Clicking noise should be heard.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 3.
3.
CHECK EVAP CANISTER VENT CONTROL VALVE POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
-
Disconnect EVAP canister vent control valve (3) harness con-
nector.
-
Fuel filler pipe (top of frame view) (1)
-
EVAP control system pressure sensor (2)
-
EVAP canister (4)
-
Drain filter (5)
-
: Vehicle front
2.
Turn ignition switch ON.
3.
Check voltage between EVAP canister vent control valve termi-
nal 2 and ground with CONSULT-III or tester.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E41, C1
• IPDM E/R harness connector E119
• Harness for open or short between EVAP canister vent control valve and IPDM E/R
>> Repair harness or connectors.
5.
CHECK EVAP CANISTER VENT CONTROL VALVE OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 117 and EVAP canister vent control valve terminal 1.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
AWBIA0134ZZ
Voltage: Battery voltage
PBIB0192E
Continuity should exist.
2009 Pathfinder
P0447 EVAP CANISTER VENT CONTROL VALVE
EC-721
< COMPONENT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
6.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E41, C1
• Harness for open or short between EVAP canister vent control valve and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK RUBBER TUBE FOR CLOGGING
1.
Disconnect rubber tube connected to EVAP canister vent control valve.
2.
Check the rubber tube for clogging.
OK or NG
OK
>> GO TO 8.
NG
>> Clean the rubber tube using an air blower.
8.
CHECK DRAIN FILTER
EC-721, "Component Inspection"
OK or NG
OK
>> GO TO 9.
NG
>> Replace drain filter.
9.
CHECK EVAP CANISTER VENT CONTROL VALVE
EC-721, "Component Inspection"
OK or NG
OK
>> GO TO 10.
NG
>> Replace EVAP canister vent control valve.
10.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003936654
EVAP CANISTER VENT CONTROL VALVE
With CONSULT-III
1.
Remove EVAP canister vent control valve from EVAP canister.
2.
Check portion B of EVAP canister vent control valve for being
rusted.
If NG, replace EVAP canister vent control valve.
If OK, go to next step.
3.
Reconnect harness connectors disconnected.
4.
Turn ignition switch ON.
5.
Perform “VENT CONTROL/V” in “ACTIVE TEST” mode.
6.
Check air passage continuity and operation delay time.
Check that new O-ring is installed properly.
Operation takes less than 1 second.
If NG, go to next step.
7.
Clean the air passage (portion A to B) of EVAP canister vent control valve using an air blower.
8.
Perform step 6 again.
VENT CONTROL/V Condition
Air passage continuity between A and B
ON
No
OFF
Yes
PBIB1033E
2009 Pathfinder
EC-722
< COMPONENT DIAGNOSIS >
[VK56DE]
P0447 EVAP CANISTER VENT CONTROL VALVE
9.
If NG, replace EVAP canister vent control valve.
Without CONSULT-III
1.
Remove EVAP canister vent control valve from EVAP canister.
2.
Check portion B of EVAP canister vent control valve for rust.
3.
Check air passage continuity and operation delay time under the
following conditions.
Check that new O-ring is installed properly.
Operation takes less than 1 second.
If NG, go to next step.
4.
Clean the air passage (portion A to B) of EVAP canister vent
control valve using an air blower.
5.
Perform step 3 again.
6.
If NG, replace EVAP canister vent control valve.
DRAIN FILTER
1.
Check visually for insect nests in the drain filter air inlet.
2.
Check visually for cracks or flaws in the appearance.
3.
Check visually for cracks or flaws in the hose.
4.
Blow air into port A and check that it flows freely out of port B.
5.
Block port B.
6.
Blow air into port A and check that there is no leakage.
7.
If NG, replace drain filter.
PBIB1033E
Condition
Air passage continuity between A and B
12V direct current supply between
terminals 1 and 2
No
OFF
Yes
PBIB1034E
PBIB3641E
2009 Pathfinder
P0448 EVAP CANISTER VENT CONTROL VALVE
EC-723
< COMPONENT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0448 EVAP CANISTER VENT CONTROL VALVE
Component Description
INFOID:0000000004333364
The EVAP canister vent control valve (3) is located on the EVAP
canister (4) and is used to seal the canister vent.
• Fuel filler pipe (top of frame view) (1)
• EVAP control system pressure sensor (2)
• Drain filter (5)
•
: Vehicle front
This solenoid valve responds to signals from the ECM. When the
ECM sends an ON signal, the coil in the solenoid valve is energized.
A plunger will then move to seal the canister vent. The ability to seal
the vent is necessary for the on board diagnosis of other evaporative
emission control system components.
This solenoid valve is used only for diagnosis, and usually remains
opened.
When the vent is closed, under normal purge conditions, the evapo-
rative emission control system is depressurized and allows “EVAP
Control System” diagnosis.
On Board Diagnosis Logic
INFOID:0000000003936656
DTC Confirmation Procedure
INFOID:0000000003936657
1.
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next step.
a.
Turn ignition switch OFF and wait at least 10 seconds.
b.
Turn ignition switch ON.
c.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON and wait at least 5 seconds.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Start engine and let it idle for at least 1 minute.
5.
Repeat next procedures 3 times.
a.
Rev engine between 3,000 and 3,500 rpm, then maintain that speed for 2 minutes and 50 seconds to 3
minutes.
Do not exceed 3 minutes.
b.
Fully released accelerator pedal and keep engine idle for approximately 5 seconds.
6.
Check 1st trip DTC.
7.
If 1st trip DTC is detected, go to
AWBIA0134ZZ
PBIB3642E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0448
0448
EVAP canister vent control
valve close
EVAP canister vent control valve remains
closed under specified driving conditions.
• EVAP canister vent control valve
• EVAP control system pressure sensor and
the circuit
• Blocked rubber tube to EVAP canister vent
control valve
• Drain filter
• EVAP canister is saturated with water
2009 Pathfinder
EC-724
< COMPONENT DIAGNOSIS >
[VK56DE]
P0448 EVAP CANISTER VENT CONTROL VALVE
If 1st trip DTC is not detected, go to the next step.
8.
Repeat next procedure 20 times.
a.
Quickly rev engine between 4,000 and 4,500 rpm or more, then maintain that speed for 25 to 30 seconds.
b.
Fully released accelerator pedal and keep engine idle for at least 35 seconds.
9.
Check 1st trip DTC.
10. If 1st trip DTC is detected, go to
Diagnosis Procedure
INFOID:0000000003936658
1.
CHECK RUBBER TUBE
1.
Turn ignition switch OFF.
2.
Disconnect rubber tube connected to EVAP canister vent control
valve (3).
-
Fuel filler pipe (top of frame view) (1)
-
EVAP control system pressure sensor (2)
-
EVAP canister (4)
-
Drain filter (5)
-
: Vehicle front
3.
Check the rubber tube for clogging.
OK or NG
OK
>> GO TO 2.
NG
>> Clean rubber tube using an air blower.
2.
CHECK DRAIN FILTER
EC-725, "Component Inspection"
OK or NG
OK
>> GO TO 3.
NG
>> Replace drain filter.
3.
CHECK EVAP CANISTER VENT CONTROL VALVE
EC-725, "Component Inspection"
OK or NG
OK
>> GO TO 4.
NG
>> Replace EVAP canister vent control valve.
4.
CHECK IF EVAP CANISTER IS SATURATED WITH WATER
1.
Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
JMBIA1516GB
AWBIA0134ZZ
2009 Pathfinder
P0448 EVAP CANISTER VENT CONTROL VALVE
EC-725
< COMPONENT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
Check if water will drain from the EVAP canister.
Yes or No
Yes
>> GO TO 5.
No
>> GO TO 7.
5.
CHECK EVAP CANISTER
Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.0 kg (4.4 lb).
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
• EVAP canister for damage
• EVAP hose between EVAP canister and drain filter for clogging or poor connection
>> Repair hose or replace EVAP canister.
7.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR
1.
Disconnect EVAP control system pressure sensor harness connector.
2.
Check connectors for water.
OK or NG
OK
>> GO TO 8.
NG
>> Replace EVAP control system pressure sensor.
8.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-730, "Component Inspection"
OK or NG
OK
>> GO TO 9.
NG
>> Replace EVAP control system pressure sensor.
9.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000004333365
EVAP CANISTER VENT CONTROL VALVE
With CONSULT-III
1.
Remove EVAP canister vent control valve from EVAP canister.
BBIA0558E
Water should not exist.
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст