Nissan Pathfinder (2009 year). Instruction — part 247
DLN-458
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
REAR FINAL DRIVE
5.
Press the drive pinion assembly (with rear inner bearing race
and collapsible spacer) out of the gear carrier.
CAUTION:
Do not drop drive pinion assembly.
6.
Remove the front oil seal.
CAUTION:
Do not damage gear carrier.
7.
Remove the drive pinion front bearing inner race.
8.
Remove the drive pinion rear bearing inner race and drive pinion
height adjusting washer using Tool.
9.
Remove the drive pinion front and rear bearing outer races by
tapping them uniformly using suitable tool.
CAUTION:
Do not damage gear carrier.
INSPECTION AFTER DISASSEMBLY
Clean the disassembled parts. Then inspect the parts for wear or damage. If wear or damage are found, follow
the measures below.
Drive Pinion and Drive Gear
• If the drive pinion and drive gear teeth do not mesh or line-up correctly, determine the cause and adjust,
repair, or replace as necessary.
• If the drive pinion or drive gear are worn, cracked, damaged, pitted or chipped (by friction) noticeably,
replace with new drive pinion and drive gear.
• Drive pinion and drive gear are supplied in matched sets only. Matching numbers on both drive pinion and
drive gear are etched for verification. If a new drive pinion and drive gear set are being used, verify the num-
bers of each drive pinion and drive gear before proceeding with assembly.
Bearing
• If bearings are chipped (by friction), pitted, worn, rusted, scratched, or unusual noise is coming from bearing,
replace with new bearing assembly (as a new set).
• Bearing must be replaced with a new one whenever disassembled.
Side Gear and Pinion Mate Gear
• If any cracks or damage are found on the surface of the teeth, replace with new one.
• If any worn or chipped marks are found on the side of the side gear and pinion mate gear which contact the
thrust washer, replace with new one.
• Replace both side gear and pinion mate gear as a set when replacing side gear or pinion mate gear.
Side Gear Thrust Washer and Pinion Mate Thrust Washer
• If any chips (by friction), damage, or unusual wear are found, replace with new one.
SPD892
Tool number:
: ST30031000 (J-22912-01)
S-PD179
SDIA0817E
2009 Pathfinder
REAR FINAL DRIVE
DLN-459
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Gear Carrier
• If any wear or cracks are found on the contact sides of gear carrier, replace with new one.
Companion Flange
• If any chips (about 0.1mm, 0.004 in) or other damage on the companion flange surface which contacts the
front oil seal lips are found, replace with new one.
ADJUSTING AND SELECTING WASHERS
Side Gear Back Clearance
• Assemble the differential parts if they are disassembled. Refer to
DLN-450, "Disassembly and Assembly"
1.
Place the differential case straight up so that the side gear to be
measured is upward.
2.
Using feeler gauges, measure the clearance between the side
gear back and differential case at three different points, while
rotating the side gear. Average the three readings to calculate
the clearance. (Measure the clearance of the other side as well.)
• If the side gear back clearance is outside of the specification,
use a thicker or thinner side gear thrust washer to adjust.
Refer to
DLN-467, "Inspection and Adjustment"
CAUTION:
• Insert feeler gauges with the same thickness on both
sides to prevent side gear from tilting.
• Each gear should rotate smoothly without excessive
resistance during differential motion.
• Select a side gear thrust washer for right and left individu-
ally.
NOTE:
Side gear back clearance is clearance between side gear and differential case for adjusting side gear
backlash.
Side Bearing Preload Torque
• A selection of side bearing adjusting washers is required for successful completion of this procedure.
PDIA0460E
Side gear back clearance:
0.20 mm (0.0079 in) or less.
If the side gear back clearance is greater than
specification:
Use a thicker side gear thrust washer.
If the side gear back clearance is less than spec-
ification:
Use a thinner side gear thrust washer.
PDIA0576E
2009 Pathfinder
DLN-460
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
REAR FINAL DRIVE
1.
Apply differential gear oil to the side bearings, and install the dif-
ferential case assembly with the side bearing outer races into
the gear carrier.
CAUTION:
Do not reuse side bearing outer race when replacing side
bearing inner race (replace as a set).
2.
Insert the left and right original side bearing adjusting washers in
place between side bearings and gear carrier.
3.
Align the matching mark on the side bearing cap with the match-
ing mark on the gear carrier.
4.
Install the side bearing caps and tighten the side bearing cap
bolts to the specified torque. Refer to
.
5.
Turn the differential assembly several times to seat the side
bearings.
6.
To determine side bearing preload torque, measure the pulling
force of the differential assembly at the drive gear bolt using
Tool.
NOTE:
If pulling force of the differential assembly at the drive gear bolt
is within specification, side bearing preload torque will also be
within specification. Refer to
DLN-467, "Inspection and Adjustment"
SPD527
SPD924
SDIA1795E
Tool number
:
—
(J-8129)
Specification
: 34.2 - 39.2 N (3.5 - 4.0 kg, 7.7 - 8.8 lb)
of pulling force at the drive gear bolt
SPD194A
2009 Pathfinder
REAR FINAL DRIVE
DLN-461
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
7.
If the pulling force is outside the specification, use a thicker or
thinner side bearing adjusting washer to adjust. Refer to
467, "Inspection and Adjustment"
.
CAUTION:
Select a side bearing adjusting washer for right and left
individually.
8.
Record the total amount of washer thickness required for the correct side bearing preload torque.
ASSEMBLY
Drive Pinion Assembly
1.
Install the drive pinion front and rear bearing outer races using
Tools.
CAUTION:
Do not reuse drive pinion front and rear bearing outer race.
2.
Select a drive pinion height adjusting washer. Refer to
DLN-467, "Inspection and Adjustment"
.
3.
Install the selected drive pinion height adjusting washer to the
drive pinion. Press the drive pinion rear bearing inner race to it
using Tool.
CAUTION:
• Install the drive pinion height adjusting washer in the
proper direction as shown.
• Do not reuse drive pinion rear bearing inner race.
If the pulling force is less than the specification:
Use a thicker side bearing adjusting washer.
If the pulling force is greater than the specification:
Use a thinner side bearing adjusting washer.
SPD772
Tool number
A: ST15310000 (
—
)
B: ST35325000 (
—
)
C: ST30621000 (J-25742-5)
SPD992
Tool number
: ST30022000 (
—
)
SPD377
2009 Pathfinder
DLN-462
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
REAR FINAL DRIVE
4.
Assemble the collapsible spacer to the drive pinion.
CAUTION:
Do not reuse collapsible spacer.
5.
Apply differential gear oil to the drive pinion rear bearing, and
install the drive pinion assembly to the gear carrier.
6.
Apply differential gear oil to the drive pinion front bearing, and
install the drive pinion front bearing inner race to the drive pinion
assembly.
CAUTION:
Do not reuse drive pinion front bearing inner race.
7.
Press the drive pinion front bearing inner race to the drive pinion
as far as drive pinion lock nut can be tightened using suitable
spacer.
8.
Apply multi-purpose grease to the lips of the new front oil seal.
Then drive the new front oil seal in evenly until it becomes flush
with the gear carrier using Tool.
CAUTION:
• Do not reuse front oil seal.
• Do not incline the new front oil seal when installing.
• Apply multi-purpose grease to the lips of the new front oil
seal.
9.
Install the companion flange to the drive pinion while aligning the matching marks.
PDIA0492E
SPD896
Tool number
: ST15310000 (
—
)
PDIA0563E
2009 Pathfinder
REAR FINAL DRIVE
DLN-463
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
10. Apply anti-corrosive oil to the threads of the drive pinion and the
seating surface of the new drive pinion lock nut. Then adjust the
drive pinion lock nut tightening torque using Tool A, and check
the drive pinion bearing preload torque using Tool B.
CAUTION:
• Do not reuse drive pinion lock nut.
• Apply anti-corrosive oil to the threads of the drive pinion
and the seating surface of the new drive pinion lock nut.
• Adjust the drive pinion lock nut tightening torque to the
lower limit first. Do not exceed the drive pinion lock nut
specified torque. Refer to
.
• If the drive pinion bearing preload torque exceeds the
specified value, replace collapsible spacer and tighten it
again to adjust. Do not loosen drive pinion lock nut to
adjust the drive pinion bearing preload torque.
• After adjustment, rotate drive pinion back and forth 2 to 3
times to check for unusual noise, rotation malfunction, and other malfunctions.
11. Check companion flange runout. Refer to
DLN-467, "Inspection and Adjustment"
.
12. Install the differential case assembly. Refer to
DLN-450, "Disassembly and Assembly"
.
Differential Assembly
1.
Install side gear thrust washers with the same thickness as the
ones installed prior to disassembly, or reinstall the old ones on
the side gears.
2.
Install the side gears and side gear thrust washers into the dif-
ferential case.
CAUTION:
Make sure that the circular clip is installed to side gears.
3.
Install the pinion mate thrust washers to the two pinion mate
gears. Then install the pinion mate gears with the pinion mate
thrust washers by aligning them in diagonally opposite positions
and rotating them into the differential case.
Tool number
A: KV40104000 (
—
)
B: ST3127S000 (J-25765-A)
Drive pinion bearing preload torque:
1.77 - 2.64 N·m (0.18 - 0.26 kg-m, 16 - 23 in-lb)
WDIA0379E
SDIA0193J
SDIA2025E
2009 Pathfinder
DLN-464
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
REAR FINAL DRIVE
4.
Align the lock pin hole on the differential case with the lock pin
hole on the pinion mate shaft, and install the pinion mate shaft.
5.
Measure the side gear end play. If necessary, select the appro-
priate side gear thrust washers. Refer to
6.
Drive a new lock pin into the pinion mate shaft until it is flush
with the differential case using suitable tool.
CAUTION:
Do not reuse lock pin.
7.
Align the matching mark of the differential case with the mark of
the drive gear, then place the drive gear onto the differential
case.
8.
Apply thread locking sealant into the threaded holes of the drive
gear and install the bolts.
• Use Genuine Medium Strength Thread Locking Sealant or
equivalent. Refer to
GI-26, "Recommended Chemical Prod-
CAUTION:
Make sure the drive gear back and threaded holes are
clean.
9.
Tighten the drive gear bolts to the specified torque. Refer to
DLN-450, "Disassembly and Assembly"
. After tightening the
drive gear bolts to the specified torque, tighten an additional 34
°
using Tool.
CAUTION:
• Always use Tool. Avoid tightening based on visual check
alone.
• Tighten drive gear bolts in a crisscross pattern.
SDIA0195J
WDIA0131E
SDIA2593E
SDIA2594E
Tool number
: KV10112100-A (BT-8653-A)
AWBIA0722ZZ
2009 Pathfinder
REAR FINAL DRIVE
DLN-465
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230 (4WD)]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
10. Press the side bearing inner races into the differential case
using Tools.
CAUTION:
Do not reuse side bearing inner race.
11. Install the differential case assembly with the side bearing outer
races into the gear carrier.
12. Measure the side bearing preload torque. If necessary, select
the appropriate side bearing adjusting washers. Refer to
467, "Inspection and Adjustment"
"Side Bearing Preload
Torque".
13. Insert the selected left and right side bearing adjusting washers
in place between the side bearings and gear carrier.
14. Install the side bearing caps with the matching marks aligned
and tighten the side bearing cap bolts to the specified torque.
Refer to
DLN-450, "Disassembly and Assembly"
15. Check and adjust the drive gear runout, tooth contact, drive gear to drive pinion backlash, and total pre-
DLN-467, "Inspection and Adjustment"
.
Recheck the above items.
16. Install the side flanges. Refer to
DLN-444, "Removal and Installation"
.
Tool number
A: KV38100200 (J-26233)
B: ST33081000 (
—
)
SPD353
SPD919
SPD924
SPD889
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст