Nissan Pathfinder (2009 year). Instruction — part 8
LIFTING SWITCH (REAR)
ADP-51
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1.
Connect the driver seat control unit.
2.
Turn ignition switch ON.
3.
Check voltage between driver seat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Replace driver seat control unit. Refer to
4.
CHECK LIFTING SWITCH (REAR)
ADP-51, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> Replace power seat switch LH. Refer to
.
5.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
NO
>> Repair or replace the malfunctioning part.
Component Inspection
INFOID:0000000003935524
1.
CHECK LIFTING SWITCH (REAR)
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch LH.
3.
Check continuity between power seat switch LH terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace power seat switch LH. Refer to
.
Driver seat control unit
connector
Terminal
Ground
Continuity
B202 (A)
14
No
29
Driver seat control unit
connector
Terminals
Voltage (V)
(Approx.)
(+)
(–)
B202
14
Ground
Battery voltage
29
PIIA4586E
Terminal
Condition
Continuity
Power seat switch LH
7
2
Lifting switch rear (up)
Operate
Yes
Release
No
6
Lifting switch rear (down)
Operate
Yes
Release
No
ALJIA0315ZZ
2009 Pathfinder
ADP-52
< COMPONENT DIAGNOSIS >
PEDAL ADJUSTING SWITCH
PEDAL ADJUSTING SWITCH
Description
INFOID:0000000003935525
Pedal adjusting switch is on the instrument panel. The operation signal is input to the driver seat control unit
when the pedal adjusting switch is operated. The pedal adjusting switch signal is sent to the automatic drive
positioner control unit via UART communication.
Component Function Check
INFOID:0000000003935526
1.
CHECK FUNCTION
1.
Select “PEDAL SW-FR”, “PEDAL SW-RR” in “Data monitor” mode with CONSULT-III.
2.
Check pedal adjusting switch signal under the following conditions.
Is the indication normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000003935527
1.
CHECK PEDAL ADJUSTING SWITCH SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between driver seat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> GO TO 2
2.
CHECK PEDAL ADJUSTING SWITCH CIRCUIT
Monitor item
Condition
Status
PEDAL SW-FR
Pedal adjusting switch (forward)
Operate
ON
Release
OFF
PEDAL SW-RR
Pedal adjusting switch (backward)
Operate
ON
Release
OFF
Driver seat
control unit
connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
B202
15
Ground
Pedal ad-
justing
switch
Operate
(backward)
0
Release
Battery
voltage
30
Operate
(forward)
0
Release
Battery
voltage
PIIA4591E
2009 Pathfinder
PEDAL ADJUSTING SWITCH
ADP-53
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit and pedal adjusting switch.
3.
Check continuity between driver seat control unit harness con-
nector and pedal adjusting switch harness connector.
4.
Check continuity between driver seat control unit harness con-
nector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1.
Connect the driver seat control unit.
2.
Turn ignition switch ON.
3.
Check voltage between driver seat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Replace driver seat control unit. Refer to
4.
CHECK PEDAL ADJUSTING SWITCH
ADP-54, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> Replace pedal adjusting switch.
5.
CHECK PEDAL ADJUSTING SWITCH GROUND CIRCUIT
Check continuity between pedal adjusting switch connector M96 ter-
minal 1 and ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Replace or replace harness.
6.
CHECK INTERMITTENT INCIDENT
Driver seat
control unit
connector
Terminal
Pedal adjusting
switch connector
Terminal
Continuity
B202
15
M96
2
Yes
30
3
Driver seat control unit
connector
Terminal
Ground
Continuity
B202
15
No
30
LIIA0726E
Driver seat control unit
connector
Terminals
Voltage (V)
(Approx.)
(+)
(–)
B202
15
Ground
Battery voltage
30
PIIA4591E
1 - Ground
: Continuity should exist.
LIIA1015E
2009 Pathfinder
ADP-54
< COMPONENT DIAGNOSIS >
PEDAL ADJUSTING SWITCH
GI-49, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-159, "Removal and Installation"
NO
>> Repair or replace the malfunctioning part.
Component Inspection
INFOID:0000000003935528
1.
CHECK PEDAL ADJUSTING SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect pedal adjusting switch.
3.
Check continuity between pedal adjusting switch terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace pedal adjusting switch.
Terminal
Condition
Continuity
Pedal adjusting switch
1
2
Pedal adjusting switch
(backward)
Operate
Yes
Release
No
3
Pedal adjusting switch
(forward)
Operate
Yes
Release
No
LIIA1014E
2009 Pathfinder
SEAT MEMORY SWITCH
ADP-55
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
SEAT MEMORY SWITCH
Description
INFOID:0000000003935529
Memory switch is equipped on the seat memory switch installed to the front door LH trim. The operation signal
is input to the automatic drive positioner control unit when the memory switch is operated.
Component Function Check
INFOID:0000000003935530
1.
CHECK FUNCTION
1.
Select “MEMORY SW 1”, “MEMORY SW 2”, "SET SW" in “Data monitor” mode with CONSULT-III.
2.
Check seat memory switch signal under the following conditions.
Is the indication normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000003935531
1.
CHECK MEMORY SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and seat
memory switch.
3.
Check continuity between automatic drive positioner control unit
harness connector and seat memory switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace harness.
2.
CHECK MEMORY SWITCH GROUND CIRCUIT
Monitor item
Condition
Status
MEMORY SW1
Memory switch 1
Push
ON
Release
OFF
MEMORY SW2
Memory switch 2
Push
ON
Release
OFF
SET SW
Set switch
Push
ON
Release
OFF
Automatic drive
positioner control
unit connector
Terminal
Seat memory
switch connector
Terminal
Continuity
M33
9
D5
1
Yes
24
3
25
2
Automatic drive positioner
control unit connector
Terminal
Ground
Continuity
M33
9
No
24
25
PIIA4576E
2009 Pathfinder
A
D
P
- 5
6
< COMPONENT DIAGNOSIS >
SEAT MEMORY SWITCH
Check continuity between seat memory switch harness connector
and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK SEAT MEMORY SWITCH
ADP-56, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Replace seat memory switch. Refer to
INT-14, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-159, "Removal and Installation"
NO
>> Repair or replace the malfunctioning part.
Component Inspection
INFOID:0000000003935532
1.
CHECK SEAT MEMORY SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect seat memory switch.
3.
Check continuity between seat memory switch terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace seat memory switch.
Seat memory switch
connector
Terminal
Ground
Continuity
D5
4
Yes
PIIA4821E
Terminal
Condition
Continuity
Seat memory switch
4
1
Memory switch 1
Push
Yes
Release
No
2
Memory switch 2
Push
Yes
Release
No
3
Set switch
Push
Yes
Release
No
LIIA1020E
2009 Pathfinder
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-57
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Description
INFOID:0000000003935533
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Component Function Check
INFOID:0000000003935534
1.
CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.
Refer to
ADP-25, "CONSULT-III Function"
.
Is the inspection result normal?
YES
>> Changeover switch function is OK.
NO
>> Refer to
ADP-57, "CHANGEOVER SWITCH : Diagnosis Procedure"
.
CHANGEOVER SWITCH : Diagnosis Procedure
INFOID:0000000003935535
1.
CHECK CHANGEOVER SWITCH SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between automatic drive positioner control unit
connector and ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> GO TO 2
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and door mir-
ror remote control switch.
3.
Check continuity between automatic drive positioner control unit
connector and door mirror remote control switch connector.
4.
Check continuity between automatic drive positioner control unit connector and ground.
Terminals
Change over switch
condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner control
unit connector
Terminal
M33
2
Ground
RIGHT
0
Other than above
5
18
LEFT
0
Other than above
5
PIIA4767E
Automatic drive
positioner control
unit connector
Terminal
Door mirror re-
mote control
switch connector
Terminal
Continuity
M33
2
M163
3
Yes
18
2
LIIA1821E
2009 Pathfinder
ADP-58
< COMPONENT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirror remote control switch connec-
tor and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1.
Connect automatic drive positioner control unit.
2.
Turn ignition switch ON.
3.
Check voltage between automatic drive positioner control unit
connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace automatic drive positioner control unit. Refer to
ADP-159, "Removal and Installation"
5.
CHECK CHANGEOVER SWITCH
Check changeover switch.
Refer to
ADP-58, "CHANGEOVER SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> Refer to
GI-49, "Intermittent Incident"
.
NO
>> Replace door mirror remote control switch. Refer to
INT-14, "Removal and Installation"
.
6.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-49, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-159, "Removal and Installation"
NO
>> Repair or replace the malfunctioning parts.
CHANGEOVER SWITCH : Component Inspection
INFOID:0000000003935536
1.
CHECK CHANGEOVER SWITCH
Automatic drive positioner control
unit connector
Terminal
Ground
Continuity
M33
2
No
18
Door mirror remote control switch
connector
Terminal
Ground
Continuity
M163
13
Yes
LIIA1825E
Terminals
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner
control unit connector
Terminal
M33
2
Ground
5
18
PIIA4767E
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст