Nissan Pathfinder (2009 year). Instruction — part 569
HEATED SEAT
SE-21
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
ABJIA0177GB
2009 Pathfinder
SE-22
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003935857
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for Work
INFOID:0000000003935858
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and keep them.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After re-installation is completed, be sure to check that each part works normally.
• Follow the steps below to clean components.
- Water soluble foul: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the
fouled area.
Then rub with a soft and dry cloth.
- Oily foul: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the fouled area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000004454810
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
2009 Pathfinder
PRECAUTIONS
SE-23
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3.
Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6.
Perform a self-diagnosis check of all control units using CONSULT-III.
2009 Pathfinder
SE-24
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000003935859
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000003935860
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis ear
Locating the noise
—
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear
Locating the noise
SIIA0995E
2009 Pathfinder
FRONT SEAT
SE-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
ON-VEHICLE REPAIR
FRONT SEAT
Exploded View
INFOID:0000000003935861
Power Driver Seat
LIIA2406E
2009 Pathfinder
SE-26
< ON-VEHICLE REPAIR >
FRONT SEAT
1.
Headrest
2.
Seatback pad without side air bag
3.
Seatback heating element
4.
Seatback assembly with side air bag 5.
Seatback trim without side air bag
6.
Power seat cushion rear finisher
7.
Leg Cover
8.
Lifter motor link bar
9.
Seat belt buckle assembly
10. Seat cushion inner finisher
11. Seat frame assembly
12. Seat lifter motor assembly
13. Seat spacer
14. Lock gear
15. Seat cushion front finisher
16. Flexible seat wire
17. Front seat slide motor assembly (LH) 18. Power seat control assembly
19. Lifter motor bracket assembly
20. Driver seat wiring harness
21. Seat cushion outer finisher
22
Leg cover
23
Bolt cover
24. Seat cushion frame
25. Recliner switch knob
26. Slide switch knob
27. Power seat switch escutcheon
28. Switch assembly
29. Seat cushion pad
30. Seat cushion heating element
31. Seat cushion trim
32. Lumbar support assembly
33. Seatback frame
34. Seatback board
35. Headrest holder with multi position
lock
36. Headrest holder
37. Lumbar support lever knob
38. Snap ring
2009 Pathfinder
FRONT SEAT
SE-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Instruction Driver Seat
LIIA2407E
1.
Headrest
2.
Seatback pad without side air bag
3.
Seatback trim without side air bag
4.
Seatback assembly with side air bag 5.
Seat cushion trim cover
6.
Seat cushion pad
7.
Seat cushion frame
8.
Seat cushion inner finisher
9.
Seat belt buckle assembly
10. Seat frame assembly
11. Leg cover
12. Bolt cover
13. Recline lever
14. Seat cushion outer finisher
15. Leg cover
16. Seat cushion rear finisher
17. Seat cushion lift knobs
18. Lumbar support assembly
2009 Pathfinder
SE-28
< ON-VEHICLE REPAIR >
FRONT SEAT
Conventional Passenger Seat
19. Seatback frame without side air bag
20. Seatback board
21. Headrest holder with multi position
lock
22
Headrest holder
23
Lumbar support lever knob
24. Snap ring
LIIA2408E
1.
Seatback trim without side air bag
2.
Headrest
3.
Seatback assembly with side air bag
4.
Switch assembly
5.
Power seat switch escutcheon
6.
Recliner switch knob
7.
Slide switch knob
8.
Seat cushion assembly
9.
Seat cushion outer cover
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст