Nissan Qashqai (2007-2010). Manual — part 1340
PARKING LAMP CIRCUIT
EXL-65
< COMPONENT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
4.
With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.
Is the measurement value normal?
YES
>> GO TO 5.
NO
>> Replace IPDM E/R.
5.
CHECK PARKING LAMP OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between the IPDM E/R harness connector and the front combination lamp harness con-
nector.
Does continuity exist?
YES
>> GO TO 6.
NO
>> Repair the harnesses or connectors.
6.
CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between the front combination lamp harness connector and the ground.
Does continuity exist?
YES
>> Replace the front combination lamp.
NO
>> Repair the harnesses or connectors.
Terminals
Test item
Voltage
(Approx.)
(+)
(
−
)
IPDM E/R
Ground
EXTERNAL
LAMP
Connector
Terminal
RH
E13
37
TAIL
Battery
voltage
LH
47
OFF
0 V
IPDM E/R
Front combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E13
37
E43
1
Existed
LH
47
E24
1
Front combination lamp
Ground
Continuity
Connector
Terminal
RH
E43
2
Existed
LH
E24
2
EXL-66
< COMPONENT DIAGNOSIS >
[XENON TYPE]
TURN SIGNAL LAMP CIRCUIT
TURN SIGNAL LAMP CIRCUIT
Description
INFOID:0000000000955454
BCM performs the high flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is
open.
NOTE:
The turn signal lamp blinks at normal speed when using the hazard warning lamp.
Component Function Check
INFOID:0000000000955455
1.
CHECK TURN SIGNAL LAMP
CONSULT-III ACTIVE TEST
1.
Select "FLASHER" of BCM (FLASHER) active test item.
2.
With operating the test items, check that the turn signal lamp is turned ON.
Are the turn signal lamps turned ON?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000000955456
1.
CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1.
Turn the ignition switch OFF.
2.
Disconnect the front combination lamp connector, side turn signal lamp connector, or the rear combination
lamp connector.
3.
Turn the ignition switch ON.
4.
With operating the turn signal switch, check the voltage between the BCM harness connector and the
ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
LH
: Turn signal lamp (LH) ON
RH
: Turn signal lamp (RH) OFF
OFF
: The turn signal lamp OFF
Terminals
Condition
Voltage (Approx.)
(+)
(
−
)
BCM
Ground
Turn signal
switch
Connector
Terminal
RH
M66
48
LH or RH
LH
47
OFF
0 V
PKID0926E
TURN SIGNAL LAMP CIRCUIT
EXL-67
< COMPONENT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between the BCM harness connector and the front combination lamp, side turn signal
lamp or the rear combination lamp harness connector.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Does continuity exist?
YES
>> GO TO 4.
NO
>> Repair the harnesses or connectors.
4.
CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between the BCM harness connector and the ground.
Does continuity exist?
YES
>> Repair the harnesses or connectors.
NO
>> GO TO 5.
5.
CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between the BCM harness connector and the front combination lamp, side turn signal lamp
or the rear combination lamp and the ground.
Front turn signal lamp
Side turn signal lamp
BCM
Front combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M66
48
E45
3
Existed
LH
47
E26
BCM
Side turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M66
48
E40
1
Existed
LH
47
E23
BCM
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M66
48
B59
1
Existed
LH
47
B80
BCM
Ground
Continuity
Connector
Terminal
RH
M66
48
Not existed
LH
47
Front combination lamp
Ground
Continuity
Connector
Terminal
RH
E45
5
Existed
LH
E26
Side turn signal lamp
Ground
Continuity
Connector
Terminal
RH
E40
2
Existed
LH
E23
EXL-68
< COMPONENT DIAGNOSIS >
[XENON TYPE]
TURN SIGNAL LAMP CIRCUIT
Rear turn signal lamp
Does continuity exist?
YES
>> Replace the front combination lamp, the side turn signal lamp or the rear combination lamp.
NO
>> Repair the harnesses or connectors.
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B59
4
Existed
LH
B80
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст