Nissan Qashqai (2007-2010). Manual — part 1242
SEC-168
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM
Component Description
INFOID:0000000001097667
7.
BCM
M65, M66, M67
8.
Siren control unit
M94
9.
Ultra sonic sensor LH
R11
10. Ultra sonic sensor RH
R12
11. Security indicator lamp
(built in combination meter)
M34
A.
Engine room (LH)
B.
View with front bumper removed
C.
Engine room (RH)
D.
View with center pillar
E.
View with back door opened
F.
View with luggage side lower finisher
(LH) removed
G.
Over the glove box
H.
Over the glove box
I.
Built in combination meter
Component Reference
BCM
Horn
Hood switch
Security indicator
Door switch
Siren control unit
Ultra sonic sensor
NATS antenna amp.
DIAGNOSIS SYSTEM (BCM)
SEC-169
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000001097675
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
IMMU
IMMU : CONSULT-III Function (BCM - IMMU)
INFOID:0000000001097676
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
SELF-DIAG RESULTS
Displays the diagnosis results judged by BCM. Refer to
CAN DIAG SUPPORT MNTR
Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION
The BCM part number is displayed.
CONFIGURATION
• Enables to read and save the vehicle specification.
• Enables to write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
—
BCM
×
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioner
AIR CONDITONER
×
Intelligent Key system
INTELLIGENT KEY
×
Combination switch
COMB SW
×
Immobilizer
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
Signal buffer system
SIGNAL BUFFER
×
×
PTC heater system
PTC HEATER
×
×
SEC-170
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
*1
: For the vehicle Intelligent key is equipped.
ACTIVE TEST
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT ALM)
INFOID:0000000001097677
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
*1
: For vehicle equipped with Intelligent Key.
Diagnosis mode
Function Description
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from Intelligent Key unit.
Monitor item
Content
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
PUSH SW
*1
Indicates [ON/OFF] condition of ignition knob switch.
Test item
Description
THEFT IND
This test is able to check security indicator operation [ON/OFF].
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor Item
Condition
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch in ACC position.
PUSH SW
*1
Indicates [ON/OFF] condition of ignition knob switch.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
KEYKESS LOCK
*2
Indicates [ON/OFF] condition of lock signal from key fob.
KEYLESS UNLOCK
*2
Indicates [ON/OFF] condition of unlock signal from key fob.
I-KEY LOCK
*1
Indicates [ON/OFF] condition of lock signal from Intelligent Key.
I-KEY UNLOCK
*1
Indicates [ON/OFF] condition of unlock signal from Intelligent Key.
HOOD SW
Indicates [ON/OFF] condition of hood switch.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
BACK DOOR SW
Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
DIAGNOSIS SYSTEM (BCM)
SEC-171
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
*2
: For the vehicle equipped with remote key less entry system.
ACTIVE TEST
WORK SUPPORT
Test item
Description
THEFT IND
This test is able to check security indicator operation [ON/OFF].
VEHICLE SECURITY HORN
This test is able to check horn operation [ON].
FLASHER
This test is able to check flasher operation [LH/RH/OFF].
Test item
Description
SECURITY ALARM SET
Vehicle security function mode can be changed in this mode.
• ON: Vehicle security function is ON.
• OFF: Vehicle security function is OFF.
THEFT ALM TRG
The switch which triggered vehicle security system is recorded. This mode can be able to con-
firm and erase the record of vehicle security system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст