Nissan Qashqai (2007-2010). Manual — part 662
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-5
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000000970499
Axial end play
0.05 mm (0.002 in) or less
RAX-6
< SYMPTOM DIAGNOSIS >
[4WD]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000000970500
Use chart below you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
—
—
—
NVH in DLN section
NVH in DLN section
NVH in RAX
and RSU
sections
Refer to REAR AXLE i
n
t
h
is chart
NVH in WT
section
NVH in WT
section
Ref
e
r t
o
DRIVE
SHAFT
in this
chart
NVH in BR
section
Possible cause and SUSPECTED PARTS
Ex
ce
ss
iv
e j
o
in
t an
gl
e
Jo
in
t s
lid
in
g re
si
st
an
ce
Im
b
a
lanc
e
Im
p
rop
er i
n
s
ta
lla
tio
n
,
loo
s
en
es
s
P
a
rt
s interference
PR
OP
EL
LE
R
S
H
A
F
T
DIFFERENTIAL
REA
R
AXLE AND REAR S
U
SPENSION
REA
R
AXLE
TI
RE
S
ROAD W
H
EEL
DRIV
E
SHAFT
BR
AK
E
S
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
REAR AXLE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Judder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
PRECAUTIONS
RAX-7
< PRECAUTION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PRECAUTION
PRECAUTIONS
Precautions for Drive Shaft
INFOID:0000000001117166
CAUTION:
Note the following precautions when disassembling and assembling drive shaft.
• Joint sub-assembly does not disassemble because it is non-overhaul parts.
• Perform work in a dust-free location.
• Before disassembling and assembling, clean the parts.
• Prevent the entry of foreign objects during disassembly of the service location.
• Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a
clean cover must be placed over parts.
• Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint
adhering to parts.
• Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be
removed by blowing with air or wiping with paper shop cloths.
RAX-8
< PREPARATION >
[4WD]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000000970502
Tool number
Tool name
Description
KV38100500
Drift
a: 80 mm (3.15 in) dia.
b: 60 mm (2.36 in) dia.
Installing sensor rotor
KV40101840
Color
a: 67 mm (2.64 in) dia.
b: 85 mm (3.35 in) dia.
Installing sensor rotor
ZZA0701D
ZZA1113D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст