Nissan Qashqai (2007-2010). Manual — part 606
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
TM-359
< DISASSEMBLY AND ASSEMBLY >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DISASSEMBLY AND ASSEMBLY
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
Exploded View
INFOID:0000000000987937
Disassembly
INFOID:0000000000987938
1.
Remove transaxle assembly. Refer to
(2WD),
(4WD).
2.
Remove torque converter from transaxle assembly.
CAUTION:
Never damage bush on the inside of torque converter sleeve when removing torque converter.
3.
Remove converter housing oil seal using a flat-bladed screwdriver.
CAUTION:
Be careful not to scratch converter housing.
Assembly
INFOID:0000000000987939
Note the following, and install in the reverse order of removal.
• Drive converter housing oil seal (1) evenly using a drift (A) (commercial service tool) so that converter hous-
ing oil seal protrudes by the dimension (B” respectively.
Unit: mm (in)
1.
Transaxle assembly
2.
Converter housing oil seal
3.
Torque converter
: Apply CVT Fluid NS-2.
Refer to
for symbols not described on the above.
SCIA7904J
Commercial service tool: A
Outer diameter: 65 (2.56)
Inner diameter: 60 (2.36)
2
: Transaxle assembly
SCIA7908J
TM-360
< DISASSEMBLY AND ASSEMBLY >
[CVT: RE0F10A]
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
Unit: mm (in)
NOTE:
Converter housing oil seal pulling direction is used as the refer-
ence.
• After completing installation, check for CVT fluid leakage and CVT
fluid level. Refer to
• Attach the pawl (A) of the torque converter to the drive sprocket
hole (B) on the transaxle assembly side.
CAUTION:
• Rotate the torque converter for installing torque converter.
• Never damage the bushing inside the torque converter
sleeve when installing the converter housing oil seal.
Inspection
INFOID:0000000001116442
INSPECTION AFTER INSTALLATION
• After inserting a torque converter to the CVT, check distance (A)
with in the reference value limit.
Dimension B
1.0
±
0.5 (0.039
±
0.020)
SCIA7909J
SCIA7907J
B
: Scale
C
: Straightedge
Distance (A)
: Refer to
TM-362, "Removal and Installa-
JPDIA0115ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
TM-361
< SERVICE DATA AND SPECIFICATIONS (SDS)
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000000914729
*1: Refer to
MA-21, "Fluids and Lubricants"
.
Vehicle Speed When Shifting Gears
INFOID:0000000000914730
Numerical value data are reference values.
(rpm)
CAUTION:
Lock-up clutch is engaged when vehicle speed is approximately 18 km/h (11 MPH) to 90 km/h (56 MPH).
Stall Speed
INFOID:0000000000914731
Line Pressure
INFOID:0000000000914732
kPa (bar, kg/cm
2
, psi)
*: Reference values
Solenoid Valves
INFOID:0000000000914733
Applied model
MR20DE
2WD
4WD
CVT model
RE0F10A
CVT assembly
Model code number
1XF0D
1XF0E
Transmission gear ratio
D range
2.349 – 0.394
Reverse
1.750
Final drive
6.466
Recommended fluid
NISSAN CVT Fluid NS-2
*1
Fluid capacity
8.3 liter (7-1/4 Imp qt)
CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-2. Do not mix with other fluid.
• Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and CVT durability, and may dam-
age the CVT, which is not covered by the warranty.
Engine type
Throttle position
Shift pattern
Engine speed
At 40 km/h (25 MPH)
At 60 km/h (37 MPH)
MR20DE
8/8
“D” position
3,600 – 4,500
4,500 – 5,400
2/8
“D” position
1,200 – 3,100
1,300 – 3,500
Stall speed
2,500 – 3,000 rpm
Engine speed
Line pressure
“R” or “D” positions
At idle
750 (7.50, 7.65, 108.8)
At stall
5,700 (57.00, 58.14, 826.5)
*
TM-362
< SERVICE DATA AND SPECIFICATIONS (SDS)
[CVT: RE0F10A]
SERVICE DATA AND SPECIFICATIONS (SDS)
CVT Fluid Temperature Sensor
INFOID:0000000000914734
Primary Speed Sensor
INFOID:0000000000914735
Secondary Speed Sensor
INFOID:0000000000914736
Removal and Installation
INFOID:0000000000914737
Name
Resistance (Approx.)
Terminal
Pressure control solenoid valve B (secondary
pressure solenoid valve)
3.0 – 9.0
Ω
3
Pressure control solenoid valve A (line pressure
solenoid valve)
2
Torque converter clutch solenoid valve
12
Lock-up select solenoid valve
17.0 – 38.0
Ω
13
Name
Condition
CONSULT-III “DATA MONITOR” (Approx.)
Resistance (Approx.)
CVT fluid temperature sensor
20
°
C (68
°
F)
2.0 V
6.5 k
Ω
80
°
C (176
°
F)
1.0 V
0.9 k
Ω
Name
Condition
Data (Approx.)
Primary speed sensor
When driving [“M
1
” position, 20 km/h (12 MPH)]
800 Hz
Name
Condition
Data (Approx.)
Secondary speed sensor
When driving [“D” position, 20 km/h (12 MPH)]
500 Hz
Distance between end of converter housing and torque converter
14.4 mm (0.567 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст