Nissan Qashqai (2007-2010). Manual — part 840
INTAKE SENSOR
VTL-25
< ON-VEHICLE REPAIR >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
INTAKE SENSOR
Exploded View
INFOID:0000000001093714
Removal and Installation
INFOID:0000000001093715
REMOVAL
1.
Remove passenger front Air Bag. Refer to
SR-8, "Removal and Installation"
2.
Remove Instrument Panel. Refer to
IP-12, "Removal and Installation"
1.
Intake connector seal
2.
Blower motor assembly
3.
Heater pipe seal
4.
Air conditioner filter
5.
Air conditioner filter cover
6.
Air mix door motor (left)
7.
Air mix door lever
8.
Electrical heater
9.
Air mix door (slide door)
10. Intake sensor
11.
Evaporator and expansion valve unit 12. Center case (lower)
13. Center case (upper)
14.
Defroster door
15. Intake door motor
16. Intake motor bracket
17.
Intake connector
18. Heater core
19. Air mix door link bracket
20.
Front ventilator door
21. Slide ventilator door
22. Intake door lever
23.
Intake door box
24. Intake door
25. More door motor
26.
Air mix door link (left)
27. Heater and cooling unit case
28. Air mix door motor (right)
29.
Aspirator
30. Air mix door link (right)
E1IIA0008GB
VTL-26
< ON-VEHICLE REPAIR >
[AUTOMATIC AIR CONDITIONER]
INTAKE SENSOR
3.
Remove heater and cooling unit case.
4.
Remove low-pressure pipe 1 and high-pressure pipe 2. Refer to
HA-47, "Removal and Installation"
HR),
HA-98, "Removal and Installation"
(K9K).
CAUTION:
Cap or wrap the joint of low-pressure pipe 1, 2 and high-pressure pipe 1, 2 with suitable material such
as vinyl tape to avoid the entry of air.
5.
Slide evaporator (2) to passenger side, and then remove intake
sensor (1).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings of low-pressure pipe 1, 2 and high-pressure pipe 1, 2 with new ones, and then apply
compressor oil to it when installing it.
• Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
• Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.
• Insert piping securely until a click is heard.
• After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.
• When recharging refrigerant, check for leaks.
JPIIA0030ZZ
BLOWER UNIT
VTL-27
< ON-VEHICLE REPAIR >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
BLOWER UNIT
Exploded View
INFOID:0000000001115961
Removal and Installation
INFOID:0000000001115962
REMOVAL
1.
Remove Instrument Panel. Refer to
IP-12, "Removal and Installation"
2.
Remove steering member.
3.
Remove Heater and cooling unit assembly. Refer to
VTL-32, "Removal and Installation"
4.
Remove harness fixing clip from upper intake box.
5.
Remove door motor harness connector (B).
6.
Remove lower intake box fixing screw from heater and cooling
case.
7.
Remove intake door motor (1).
• Remove fixing screws (A).
• Remove bracket support fixing screws and bracket support.
8.
Remove blower motor.Refer to
VTL-29, "Removal and Installa-
CAUTION:
Move blower unit rightward, and remove locating pin (1
part) and joint. Then remove blower unit downward.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
1.
Hi-Level ventilation door unit assem-
bly
2.
Blower motor assembly
3.
Filter cover
4.
In-cabin microfilter
5.
Blower unit
6.
Intake door motor
7.
Intake door unit assembly
E1IIA0002GB
E1IIA0017ZZ
VTL-28
< ON-VEHICLE REPAIR >
[AUTOMATIC AIR CONDITIONER]
BLOWER UNIT
Make sure locating pin are securely inserted.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст