Nissan Qashqai (2007-2010). Manual — part 1205
SEC-20
< FUNCTION DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM
BCM shifts the phase as follows and the phase information is sent to siren control unit via communication line.
Disarmed Phase
When the vehicle is being driven or when doors are open, the theft warning system is set in the disarmed
phase on the assumption that the owner is inside or near the vehicle.
Pre-Armed Phase And Armed Phase
The vehicle security system turns into the pre-armed phase when ignition switch is in OFF position, all doors
are closed and locked (using Intelligent Key, door request switch or auto relock function). 10 seconds after the
lock operation, the system automatically shifts into the armed phase.
Condition of Activating The System
When the following condition is performed in armed phase, the system sounds the horns/siren and flashes the
head lamps for about 30 seconds.
• Hood or any door is opened.
• Ultra sonic sensor is triggered.
• Ignition switch goes ON with invalid transponder ID.
Condition of Deactivating The System
When one of the following operations is performed, the armed phase is canceled.
• Unlock the doors with Intelligent Key or door request switch.
• Ignition switch goes ON with transponder ID verified.
SIREN CONTROL UNIT
Siren control unit manages siren. The siren control unit does not shift to armed phase in the same way as
BCM. The siren control unit goes to armed phase after about 10 seconds from lock command. If door is
opened or closed within about 20 seconds, only the siren will be activated.
Siren control unit has battery inside. If disconnect or connect battery terminal before canceling armed phase,
siren will be activated.
CAUTION:
When replace siren control unit (new one and used one), Perform “C/U INITALIZATION” with CON-
SULT-III.
Ultra Sonic Sensor Function
The ultra sonic sensor consist of two separate units, a transmitter on the left and receiver on the right mounted
on room mirror. The LH transmitter sensor sends an ultra sonic pulse of sound, and RH receiver sensor
receives the returning echo pulse.
It is possible to exclude the ultrasonic sensors.
To exclude the ultra sonic sensors:
1.
Turn the ignition switch from the OFF to the ON position.
2.
Turn the ignition switch from OFF to ON 3 times within 7 seconds.
3.
Close the doors, bonnet and press the lock button on the Intelligent Key to lock all doors.
The ultra sonic sensors are now excluded from the alarm system. All other functions of the system remain acti-
vated until the alarm system is disarmed again.
Component Parts Location
INFOID:0000000000944535
VEHICLE SECURITY SYSTEM
SEC-21
< FUNCTION DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
1.
IPDM E/R
E10,E12
2.
Horn
E51
3.
Hood switch
E113
4.
Front door switch (driver side)
B34
5.
Back door lock assembly (back door
switch)
D152
6.
Siren
B68
JMKIA0437ZZ
SEC-22
< FUNCTION DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM
Component Description
INFOID:0000000000944536
7.
BCM
M65,M66,M67
8.
Siren control unit
M94
9.
Ultra sonic sensor LH
R11
10. Ultra sonic sensor RH
R12
11. Security indicator lamp
(built in combination meter)
M34
A.
Engine room (LH)
B.
View with front bumper removed
C.
Engine room (RH)
D.
View with center pillar
E.
View with back door opened
F.
View with luggage side lower finisher
(LH) removed
G.
Over the glove box
H.
Over the glove box
I.
Built in combination meter
12. NATS antenna amp.
M26
13. Intelligent Key unit
M40
J.
View with steering column cover re-
moved
K.
Remove instrument driver lower pan-
el
JMKIA0438ZZ
Component Reference
BCM
Horn
Hood switch
Security indicator
Door switch
Siren control unit
Ultra sonic sensor
DIAGNOSIS SYSTEM (BCM)
SEC-23
< FUNCTION DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000001096688
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
IMMU
IMMU : CONSULT-III Function (BCM - IMMU)
INFOID:0000000001096689
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
SELF-DIAG RESULTS
Displays the diagnosis results judged by BCM. Refer to
CAN DIAG SUPPORT MNTR
Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION
The BCM part number is displayed.
CONFIGURATION
• Enables to read and save the vehicle specification.
• Enables to write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
—
BCM
×
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioner
AIR CONDITONER
×
Intelligent Key system
INTELLIGENT KEY
×
Combination switch
COMB SW
×
Immobilizer
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
Signal buffer system
SIGNAL BUFFER
×
×
PTC heater system
PTC HEATER
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст