Nissan Qashqai (2007-2010). Manual — part 963
INT-12
< ON-VEHICLE REPAIR >
DOOR FINISHER
9.
Remove front door finisher.
10. Remove the following parts after removing door finisher.
• Power window switch front. Refer to
PWC-83, "Removal and Installation"
• Seal assembly front door inside.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
REAR DOOR FINISHER
REAR DOOR FINISHER : Exploded View
INFOID:0000000001051075
1.
Power window switch front (Driver)
2.
Front door grip
3.
Front door finisher (LH)
4.
Cap-Front door grip (LH)
5.
Seal assembly front door inside (LH) 6.
Cover front door inner (LH)
7.
Front door panel
8.
Power window switch rear (LH)
9.
Inside handle escutcheon (rear LH)
10. Rear door finisher (LH)
11. Rear door panel
12. Cover rear door inner (LH)
13. Seal assembly rear door inside (LH)
: Clip
JMJIA0247ZZ
DOOR FINISHER
INT-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
REAR DOOR FINISHER : Removal and Installation
INFOID:0000000001051076
REMOVAL
1.
Fully open door window.
2.
Insert remover tool (A) between door finisher and inside handle
escutcheon (rear LH) to disengage the escutcheon retaining
pawls to door finisher.
3.
Remove inside handle escutcheon.
4.
Insert remover tool (A) between door finisher and door panel to
disengage door finisher mounting clips, starting from the bottom
and working to the top.
5.
Disconnect harness connector (A) for power window switch rear.
6.
Remove rear door finisher.
7.
Remove the following parts after removing door finisher.
• Power window switch rear. Refer to
PWC-83, "Removal and Installation"
.
• Seal assembly rear door inside.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
: Pawl
: Metal clip
: Pawl
JMJIA0255ZZ
: Clip
JMJIA0256ZZ
JMJIA0257ZZ
INT-14
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
BODY SIDE TRIM
Exploded View
INFOID:0000000000892100
Removal and Installation
INFOID:0000000000892101
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
REMOVAL
FRONT PILLAR GARNISH
1.
Remove welt body side front (RH).
1.
Front pillar garnish
2.
Dash side finisher
3.
Welt body side front (RH)
4.
Front kicking plate inner
5.
Rear kicking plate inner
6.
Center pillar lower garnish
7.
Luggage side lower finisher (front)
8.
Welt body side rear (RH)
9.
Center pillar upper garnish
10. Rear pillar finisher (RH)
11. Rear seat belt escutcheon
12. Clip-trim
: Clip
: Pawl
: Metal clip
JMJIA0239ZZ
BODY SIDE TRIM
INT-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Disengage front pillar garnish mounting pawls using remover
tool (A).
3.
Once free, pull front pillar garnish upwards to disengage the lower locating tab from instrument panel.
4.
Remove front pillar garnish.
FRONT KICKING PLATE INNER
1.
Disengage front kicking plate inner mounting pawls using
remover tool (A).
2.
Pull upwards and rearwards to disengage the clips from body, dash side finisher and center pillar lower
garnish.
3.
Remove front kicking plate inner.
REAR KICKING PLATE INNER
1.
Insert remover tool (A) between rear kicking plate inner and
body side panel to disengage pawls.
2.
Pull upwards to disengage the pawls from the body, center pillar lower garnish and luggage side lower fin-
isher (front).
3.
Remove rear kicking plate inner.
CENTER PILLAR LOWER GARNISH
1.
Remove front and rear kicking plate.
: Pawl
JMJIA0240ZZ
: Pawl
JMJIA0241ZZ
: Pawl
JMJIA0242ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст