Nissan Qashqai (2007-2010). Manual — part 784
B1023 PASS A/B INDCTR CKT
SRC-23
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1023 PASS A/B INDCTR CKT
Description
INFOID:0000000001069771
DTC B1023 PASS A/B INDCTR CKT
It is possible to suppress the deployment of passenger air bag by turning to OFF position the deactivation
switch. Passenger air bag cut
−
off indicator illuminates when the deactivation switch is turned to the OFF posi-
tion. In case of malfunction the blinking of the SRS air bag warning lamp tells the trouble to driver and by the
on board self-diagnosis system or electro diagnosis tester CONSULT-III can detects the cause.
OPERATION
Passenger air bag cut
−
off indicator illuminates when the deactivation switch is turned to the OFF position.-
STRUCTURE
Passenger air bag cut
−
off indicator with LED illumination.
INSTALLATION
Passenger air bag cut
−
off indicator is installed at the instrument panel center.
DTC Logic
INFOID:0000000001069772
DTC DETECTION LOGIC
With CONSULT-III
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
Without CONSULT-III
Warning Lamp Flash Code Chart
DTC CONFIRMATION PROCEDURE (With CONSULT-III)
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2.
2.
CONSULT-III
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1023
PASS A/B INDCTR CKT
[UNIT FAIL]
Cut
−
off indicator circuit is open or short-
ed to ground or the circuits are shorted
each other.
1.
Visually check the wiring harness
connection.
2.
Replace the harness if it has visi-
ble damage.
3.
Replace front passenger air bag
cut
−
off indicator unit.
4.
Replace diagnosis sensor unit
(ACU).
JMHIA0233GB
SRC-24
< COMPONENT DIAGNOSIS >
B1023 PASS A/B INDCTR CKT
Check the “SELF-DIAG” RESULT with CONSULT-III.
>> GO TO 3.
3.
DTC CODE
If DTC is detected. Refer to
>> END
DTC CONFIRMATION PROCEDURE (Without CONSULT-III)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2.
2.
USER MODE-DIAG MODE
After air bag warning lamp illuminates for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3.
3.
USER MODE-DIAG MODE
Wait more than 3 seconds.
>> GO TO 4.
4.
USER MODE-DIAG MODE
Repeat step 1 to 3 twice. (Perform three times in all.)
>> GO TO 5.
5.
DIAG MODE
Turn ignition switch ON. (SRS is now in diagnosis mode.)
>> GO TO 6.
6.
DIAG MODE (AIR BAG WARNING LAMP)
Malfunctioning portion is indicated according to blinking times of air bag warning lamp. Refer to
>> END
Diagnosis Procedure (Component diagnosis)
INFOID:0000000001069773
B1023 PASS A/B INDCTR CKT
SRC-25
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
With CONSULT-III
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Are connections of harness connectors and terminals correct?
YES
>> GO TO 2.
NO
>> Repair or replace harness connectors.
2.
CHECK WIRING HARNESS
Is the outside of wiring harness normal, without any damage?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK PASSENGER AIR BAG CUT
−
OFF INDICATOR
Is “PASSENGER AIR BAG CUT-OFF INDICATOR” displayed on CONSULT-III?
YES
>> Replace passenger air bag cut
−
off indicator.
NO
>> Replace diagnosis sensor unit (ACU).
SRC-26
< COMPONENT DIAGNOSIS >
B1024 PASS A/B DEACT SW
B1024 PASS A/B DEACT SW
Description
INFOID:0000000001070050
DTC B1024 PASS A/B DEACT SW
It is possible to suppress the deployment of passenger air bag by turning to OFF position the deactivation
switch. Passenger air bag cut-off indicator illuminates when the deactivation switch is turned to the OFF posi-
tion. In case of malfunction the blinking of the SRS air bag warning lamp tells the trouble to driver and by the
on board self-diagnosis system or electro diagnosis tester CONSULT-III can detects the cause.
OPERATION
Passenger air bag cut-off indicator illuminates when the deactivation switch is turned to the OFF position.
STRUCTURE
Deactivation switch controls passenger air bag module deployments ON/OFF operation.
INSTALLATION
Passenger air bag deactivation switch is installed at the instrument panel side.
DTC Logic
INFOID:0000000001070051
DTC DETECTION LOGIC
With CONSULT-III
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
Without CONSULT-III
Warning Lamp Flash Code Chart
DTC CONFIRMATION PROCEDURE (With CONSULT-III)
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2.
2.
CONSULT-III
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1024
PASS A/B DEACT SW
[UNIT FAIL]
Cut
−
off telltale circuit is open or shorted
to ground or the circuits are shorted
each other.
1.
Visually check the wiring harness
connection.
2.
Replace the harness if it has visi-
ble damage.
3.
Replace front passenger air bag
deactivation switch.
4.
Replace diagnosis sensor unit
(ACU).
JMHIA0228GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст