Nissan Qashqai (2007-2010). Manual — part 173
P0605 ECM
EC-211
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0605 ECM
Description
INFOID:0000000001056377
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
DTC Logic
INFOID:0000000001056378
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
1.
Turn ignition switch ON.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
1.
Turn ignition switch ON and wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1.
Turn ignition switch ON and waitait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3.
Repeat step 2 for 32 times.
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
PBIA9222J
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0605
Engine control module
A)
ECM calculation function is malfunctioning.
• ECM
B)
ECM EEP-ROM system is malfunctioning.
C)
ECM self shut-off function is malfunctioning.
EC-212
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
P0605 ECM
Diagnosis Procedure
INFOID:0000000001056379
1.
INSPECTION START
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “SELF-DIAG RESULTS” mode with CONSULT-III.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE.
See
.
With GST
1.
Turn ignition switch ON.
2.
Select Service $04 with GST.
3.
Perform DTC CONFIRMATION PROCEDURE.
See
.
Is the 1st trip DTC P0605 displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
Go to
EC-29, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
>> INSPECTION END
P1065 ECM
EC-213
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1065 ECM
Description
INFOID:0000000001077001
ECM has the memory function of the DTC memory, the air-fuel ratio
feedback compensation value memory, the Idle Air Volume Learning
value memory, etc. even when the ignition switch is turned OFF.
DTC Logic
INFOID:0000000001077002
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 1 second.
2.
Start engine and let it idle for 1 second.
3.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
4.
Repeat steps 2 and 3 for four times.
5.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001077003
1.
INSPECTION START
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “SELF-DIAG RESULTS” mode with CONSULT-III.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE.
See
.
With GST
1.
Turn ignition switch ON.
2.
Select Service $04 with GST.
3.
Perform DTC CONFIRMATION PROCEDURE.
See
.
Is the 1st trip DTC P1065 displayed again?
YES
>> GO TO 2.
PBIA9222J
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1065
Engine control module
ECM back-up RAM system does not function
properly.
• ECM
EC-214
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
P1065 ECM
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
Go to
EC-29, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст