Nissan Qashqai (2007-2010). Manual — part 908
HA-202
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER (K9K)]
CONDENSER
CONDENSER
Exploded View
INFOID:0000000001098300
Removal and Installation
INFOID:0000000001098301
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove engine cover ornament. Refer to
EM-266, "Removal and Installation"
3.
Remove front grille. Refer to
EXT-17, "Removal and Installation"
4.
Remove radiator hose, and drain coolant. Refer to
CO-56, "Removal and Installation"
.
5.
Remove upper radiator fixing bracket. Refer to
CO-56, "Removal and Installation"
.
6.
Remove radiator air-guide duct (RH). Refer to
CO-56, "Removal and Installation"
7.
Remove high-pressure pipe 1 from condenser. Refer to
HA-198, "Removal and Installation"
.
8.
Remove high-pressure flexible pipe 1 from condenser. Refer to
HA-196, "Removal and Installation"
CAUTION:
Cap or wrap the joint of low and high-pressure pipe 1 and condenser with suitable material such
as vinyl tape to avoid the entry of air.
9.
Remove harness connector from refrigerant pressure sensor.
10. Remove liquid tank pipes and liquid tank from condenser and radiator. Refer to
CO-56, "Removal and Installation"
.
CAUTION:
Cap or wrap the joint of liquid tank pipes and condenser with suitable material such as vinyl tape
to avoid the entry of air.
11. Remove radiator fixing brackets. Refer to
CO-56, "Removal and Installation"
.
12. Release radiator maintaining pawls, then pull-up the condenser assembly to release it from radiator. Refer
CO-56, "Removal and Installation"
.
13. Maintain radiator pushing back.
14. Pull upward to remove condenser.
CAUTION:
Take care do not damaged condenser or radiator.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
1.
Refrigerant pressure sensor
2.
O-ring
3.
Liquid tank bracket
4.
Liquid tank
5.
Condensor
6.
Liquid tank fixing screw
7.
Liquid tank pipe fixing screw
8.
Liquid tank pipe fixing bolt
E1KIA0064GB
CONDENSER
HA-203
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER (K9K)]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
• Replace O-rings of high-pressure flexible hose and high-pressure pipe 1 with new ones, and then
apply compressor oil to it when installing it.
• Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.
• Insert piping securely until a click is heard.
• After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.
• When recharging refrigerant, check for leaks.
HA-204
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER (K9K)]
LIQUID TANK
LIQUID TANK
Exploded View
INFOID:0000000001098304
Removal and Installation
INFOID:0000000001098305
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove engine cover ornament. Refer to
EM-266, "Removal and Installation"
3.
Remove front grille. Refer to
EXT-17, "Removal and Installation"
4.
Clean liquid tank and its surrounding area, and remove dust and rust from liquid tank.
CAUTION:
Be sure to clean carefully.
5.
Disconnect refrigerant sensor harness connector. Refer to
HA-205, "Removal and Installation"
6.
Remove air inlet tube and hose from change air cooler. Refer to
EM-266, "Removal and Installation"
.
7.
Remove radiator air-guide duct (RH) fixing clip to move air-guide duct. Refer to
.
8.
Remove liquid tank bracket support mounting screws (B).
9.
Remove high pressure pipe 1 mounting bolt (A). Refer to
198, "Removal and Installation"
10. Remove liquid tank high pressure pipe mounting bolt (A).
11. Remove liquid tank pipe bracket fixing screw (B).
CAUTION:
Cap or wrap the joint of high pressure pipe, liquid tank
pipes and condenser with suitable material such as vinyl
tape to avoid the entry of air.
12. Remove liquid tank assembly (1).
INSTALLATION
Install liquid tank, and then install liquid tank bracket on condenser.
CAUTION:
• Make sure liquid tank bracket is securely installed at protrusion of condenser. (Make sure liquid tank
bracket does not move to a position below center of liquid tank.)
• Replace O-rings of A/C piping with new ones, and then apply compressor oil to it when installing it.
• When recharging refrigerant, check for leaks.
1.
Refrigerant pressure sensor
2.
O-ring
3.
Liquid tank bracket
4.
Liquid tank
5.
Condensor
6.
Liquid tank fixing screw
7.
Liquid tank pipe fixing screw
8.
Liquid tank pipe fixing bolt
E1KIA0064GB
E1KIA0059ZZ
REFRIGERANT PRESSURE SENSOR
HA-205
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER (K9K)]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
REFRIGERANT PRESSURE SENSOR
Exploded View
INFOID:0000000001098306
Removal and Installation
INFOID:0000000001098307
REMOVAL
1.
Remove liquid tank. Refer to
2.
Fix the liquid tank (1) with a vise. Remove the refrigerant pres-
sure sensor from liquid tank adaptator with a wrench (B).
CAUTION:
Be careful not to damage liquid tank.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Apply compressor oil to O-ring of refrigerant pressure sensor when installing it.
• When recharging refrigerant, check for leaks.
1.
Refrigerant pressure sensor
2.
O-ring
3.
Liquid tank bracket
4.
Liquid tank
5.
Condensor
6.
Liquid tank fixing screw
7.
Liquid tank pipe fixing screw
8.
Liquid tank pipe fixing bolt
E1KIA0064GB
E1KIA0060ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст