Nissan Qashqai (2007-2010). Manual — part 545
GEAR OIL
TM-115
< ON-VEHICLE MAINTENANCE >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ON-VEHICLE MAINTENANCE
GEAR OIL
Exploded View
INFOID:0000000001066147
Draining
INFOID:0000000001034936
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug and then drain gear oil.
3.
Set a new gasket on drain plug and install it to clutch housing.
Tighten drain plug to the specified torque.
CAUTION:
Never reuse gasket.
Refilling
INFOID:0000000001034937
1.
Remove filler plug (1). Fill with new gear oil to transaxle.
2.
After refilling gear oil, check oil level. Refer to
3.
Set a new gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
Inspection
INFOID:0000000001034938
LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
LEVEL
1.
Remove filler plug (1).
2.
Measure oil level using a suitable gauge (A) as shown in the fig-
ure and then check if it is within the specifications.
CAUTION:
Never start engine while checking oil level.
3.
Set a new gasket on filler plug (1) and then install it to transaxle
case.
CAUTION:
JPDIC0073ZZ
A
: Suitable gauge
Oil grade and viscosity
: Refer to
.
Oil capacity (reference)
: Refer to
JPDIC0048ZZ
Oil level “L”
: Refer to
JPDIC0048ZZ
TM-116
< ON-VEHICLE MAINTENANCE >
[6MT: RS6F52A]
GEAR OIL
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
SIDE OIL SEAL
TM-117
< ON-VEHICLE REPAIR >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ON-VEHICLE REPAIR
SIDE OIL SEAL
Exploded View
INFOID:0000000001066148
Removal and Installation
INFOID:0000000001034939
REMOVAL
1.
Remove front drive shafts. Refer to
FAX-56, "Removal and Installation"
.
2.
Remove differential side oil seals using a suitable tool.
CAUTION:
Never damage transaxle case and clutch housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install differential side oil seal to clutch housing using the drift [SST:
ST33400001].
CAUTION:
• Never reuse differential side oil seal.
• When installing, never incline differential side oil seal.
• Never damage clutch housing.
• Install differential side oil seal to transaxle case using the drift
[SST: ST30720000].
CAUTION:
• Never reuse differential side oil seal.
• When installing, never incline differential side oil seal.
• Never damage transaxle case.
• Check oil level and oil leakage after installation. Refer to
.
SCIA0824E
Dimension “A”
: -0.5 - 0.5 mm (-0.020 - 0.020 in)
Dimension “A”
: -0.5 - 0.5 mm (-0.020 - 0.020 in)
SCIA1010E
TM-118
< ON-VEHICLE REPAIR >
[6MT: RS6F52A]
CONTROL LINKAGE
CONTROL LINKAGE
Exploded View
INFOID:0000000001034944
Removal and Installation
INFOID:0000000001034945
REMOVAL
1.
Remove the air cleaner case and air duct (inlet). Refer to
EM-144, "Removal and Installation"
.
2.
Remove the battery. Refer to
PG-118, "Removal and Installation"
.
1.
Bracket
2.
Shift cable
3.
Shifter lever A
4.
Selector lever
5.
Cable mounting bracket
6.
Select cable
7.
Grommet
8.
Control device assembly
9.
Control lever
10. Control lever knob
Refer to
for the symbols in the figure.
JPDIC0056GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст