Nissan Qashqai (2007-2010). Manual — part 1918

WCS-18

< COMPONENT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

COMPONENT DIAGNOSIS

POWER SUPPLY AND GROUND CIRCUIT

COMBINATION METER

COMBINATION METER : Diagnosis Procedure

INFOID:0000000000936047

1.

CHECK FUSE

Check for blown fuses.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Be sure to eliminate cause of malfunction before installing new fuse.

2.

CHECK POWER SUPPLY CIRCUIT

Check voltage between combination meter harness connector terminals 1, 2 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check harness between combination meter and fuse.

3.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect combination meter connector.

3.

Check continuity between combination meter harness connector terminals 3, 23 and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

BCM (BODY CONTROL MODULE)

BCM (BODY CONTROL MODULE) : Diagnosis Procedure

INFOID:0000000001102067

1.

CHECK FUSES AND FUSIBLE LINK

Check that the following fuses and fusible link are not fusing.

Is the fuse fusing?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is

blown.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connectors.

Battery power supply

: 8

Ignition signal

: 4

Terminal No.

Signal name

Ignition switch position

Value (Approx.)

1

Battery power supply

OFF

Battery voltage

2

Ignition signal

ON

Battery voltage

3, 23 – Ground

: Continuity should exist.

Terminal No.

Signal name

Fuses and fusible link No.

41

Battery power supply

9

57

J

38

Ignition power supply

4

WCS

POWER SUPPLY AND GROUND CIRCUIT

WCS-19

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

3.

Check voltage between BCM harness connector and ground.

Is the measurement value normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between BCM harness connector and ground.

Does continuity exist?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

Terminals

Ignition switch position

(+)

(

−

)

BCM

OFF

ACC

ON

Connector

Terminal

M65

38

Ground

Approx.

0 V

Approx.

0 V

Battery
voltage

M66

41

Battery
voltage

Battery
voltage

Battery
voltage

M67

57

BCM

Ground

Continuity

Connector

Terminal

M67

55

Existed

WCS-20

< COMPONENT DIAGNOSIS >

METER BUZZER CIRCUIT

METER BUZZER CIRCUIT

Description

INFOID:0000000000892420

• The buzzer for warning chime system is installed in the combination meter.
• The combination meter sounds the alarm buzzer based on the signals transmitted from various units.

Component Function Check

INFOID:0000000000892421

1.

CHECK OPERATION OF METER BUZZER

1.

Select “BUZZER” of “BCM” on CONSULT-III.

2.

Perform “LIGHT WARN ALM” of “ACTIVE TEST”.

Does meter buzzer beep?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK COMBINATION METER INPUT SIGNAL

Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to

MWI-72, "Removal and Installation"

.

NO

>> Replace BCM. Refer to

BCS-64, "Exploded View"

.

Diagnosis Procedure

INFOID:0000000000892422

1.

CHECK POWER SUPPLY AND GROUND CIRCUIT OF COMBINATION METER

Check power supply and ground circuit of combination meter. Refer to

WCS-18, "COMBINATION METER :

Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace malfunctioning parts.

BUZZER

Under the condition of buzzer input

: On

Except above

: Off

WCS

SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT

WCS-21

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT

Description

INFOID:0000000000892423

Transmits a seat belt buckle switch signal to the combination meter.

Component Function Check

INFOID:0000000000892424

1.

CHECK COMBINATION METER INPUT SIGNAL

Select the “Data Monitor” for the “METER/M&A” and check the “BUCKLE SW” monitor value.

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000000892425

1.

CHECK COMBINATION METER INPUT SIGNAL 1

1.

Turn ignition switch ON.

2.

Check voltage between combination meter harness connector terminal 35 and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

CHECK COMBINATION METER INPUT SIGNAL 2

Check voltage between combination meter harness connector terminal 36 and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 5.

3.

CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) SIGNAL CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect combination meter connector and front seat belt buckle switch (driver side) connector.

3.

Check continuity between combination meter harness connector terminal 35 and front seat belt buckle
switch (driver side) harness connector terminal 1.

4.

Check harness continuity between combination meter harness connector terminal 35 and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair harness or connector.

BUCKLE SW

When seat belt is fastened
(driver side)

: Off

When seat belt is unfastened
(driver side)

: On

35 – Ground

When driver seat belt is fastened

: Approx. 5 V

When driver seat belt is unfastened

: Approx. 0 V

36 – Ground

• Passenger seat getting in conditions
• When passenger seat belt is fastened

: Approx. 12 V

When passenger seat belt is unfastened

: Approx. 0 V

35 – 1

: Continuity should exist.

35 – Ground

: Continuity should not exist.