Nissan Qashqai (2007-2010). Manual — part 520
PREPARATION
TM-15
< PREPARATION >
[5MT: RS5F92R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Commercial Service Tools
INFOID:0000000001094778
—
(B. Vi. 1554)
Drift kit
Installing differential side bearing outer race
—
(B. Vi. 1175)
Installer
Installing 5th main gear
—
(B. Vi. 1666)
Drift
Installing differential side oil seal
—
(B. Vi. 1161)
Dial gauge support plate
Measuring preload of mainshaft rear bearing
—
(B. Vi. 1527)
Special spacer
Measuring preload of mainshaft rear bearing
Tool number
(Renault SST No.)
Tool name
Description
MCIA0151E
YMT035
YMT036
S-NT135
Tool name
Description
Drift
a: 55 mm (2.17 in) dia.
Removing mainshaft rear bearing outer race
Drift
a: 38 mm (1.50 in) dia.
Removing input shaft front bearing
SZNT063
SZNT063
TM-16
< PREPARATION >
[5MT: RS5F92R]
PREPARATION
Drift
a: 60 mm (2.36 in) dia.
Installing the mainshaft rear bearing outer
race
Drift
a: 55 mm (2.17 in) dia.
Removing mainshaft front bearing outer race
Drift
a: 14.5 mm (0.571 in) dia.
Installing bushing
Tool name
Description
SZNT063
SZNT063
SZNT063
GEAR OIL
TM-17
< ON-VEHICLE MAINTENANCE >
[5MT: RS5F92R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ON-VEHICLE MAINTENANCE
GEAR OIL
Exploded View
INFOID:0000000001070434
.
Draining
INFOID:0000000001070435
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug (1) and then drain gear oil.
3.
Set a new gasket on drain plug and install it to clutch housing.
Tighten drain plug to the specified torque.
CAUTION:
Never reuse gasket.
Refilling
INFOID:0000000001070436
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified limit at filler plug hole as shown.
2.
After refilling gear oil, check oil level. Refer to
3.
Set a new gasket on filler plug and then install it to transaxle
case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
Inspection
INFOID:0000000001070437
LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
LEVEL
1.
Remove filler plug (1) and check oil level at filler plug hole as
shown.
CAUTION:
Never start engine while checking oil level.
2.
Set a new gasket on filler plug and then install it to transaxle
case.
CAUTION:
Never reuse gasket.
3.
Tighten filler plug to the specified torque.
PCIB1504E
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
SCIA7119E
SCIA7119E
TM-18
< ON-VEHICLE REPAIR >
[5MT: RS5F92R]
SIDE OIL SEAL
ON-VEHICLE REPAIR
SIDE OIL SEAL
Exploded View
INFOID:0000000001070438
.
Removal and Installation
INFOID:0000000001070439
REMOVAL
1.
Remove front drive shafts. Refer to
FAX-17, "HR16DE MODELS : Removal and Installation"
.
2.
Remove differential side oil seals (1) using a suitable tool.
CAUTION:
Never damage transaxle case and clutch housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install differential side oil seals (1) to clutch housing and transaxle
case using the drift (A) [SST: — (B. Vi. 1666)].
CAUTION:
• Never reuse differential side oil seal.
• When installing, never incline differential side oil seal.
• Never damage clutch housing and transaxle case.
• Check oil level and oil leakage after installation. Refer to
JPDIC0118ZZ
B
: Transaxle case side
C
: Clutch housing side
Dimension “L
1
”
: 5.7 - 6.3 mm (0.224 - 0.248 in)
Dimension “L
2
”
: 2.4 - 3.0 mm (0.094 - 0.118 in)
JPDIC0119ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст