Nissan Qashqai (2007-2010). Manual — part 1382
TAIL LAMP CIRCUIT
EXL-233
< COMPONENT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
TAIL LAMP CIRCUIT
Component Function Check
INFOID:0000000001099369
1.
CHECK TAIL LAMP OPERATION
IPDM E/R AUTO ACTIVE TEST
1.
Activate IPDM E/R auto active test. Refer to
PCS-9, "Diagnosis Description"
2.
Check that the tail lamp is turned ON.
CONSULT-III ACTIVE TEST
1.
Select "EXTERNAL LAMP" of IPDM E/R active test item.
2.
With operating the test items, check that the tail lamp is turned ON.
Is the tail lamp turned ON?
YES
>> Tail lamp circuit is normal.
NO
>> Refer to
EXL-233, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000001099370
1.
CHECK TAIL LAMP FUSE
1.
Turn the ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the fuse fusing?
YES
>> Repair the malfunctioning part before replacing the fuse.
NO
>> GO TO 2.
2.
CHECK TAIL LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Disconnect the rear combination lamp connector.
2.
Turn the ignition switch ON.
3.
Select "EXTERNAL LAMP" of IPDM E/R active test item.
4.
With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R.
3.
CHECK TAIL LAMP OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect IPDM E/R connector.
TAIL
: Tail lamp ON
OFF
: Tail lamp OFF
Unit
Location
Fuse No.
Capacity
• Tail lamp
• License plate lamp
IPDM E/R
#49
10 A
Terminals
Test item
Voltage
(Approx.)
(+)
(
−
)
IPDM E/R
Ground
EXTERNAL
LAMP
Connector
Terminal
E13
38
TAIL
Battery volt-
age
OFF
0 V
EXL-234
< COMPONENT DIAGNOSIS >
[HALOGEN TYPE]
TAIL LAMP CIRCUIT
3.
Check continuity between the IPDM E/R harness connector and the rear combination lamp harness con-
nector.
Does continuity exist?
YES
>> GO TO 4.
NO
>> Repair the harnesses or connectors.
4.
CHECK TAIL LAMP GROUND OPEN CIRCUIT
Check continuity between the rear combination lamp harness connector and the ground.
Does continuity exist?
YES
>> Replace the rear combination lamp.
NO
>> Repair the harnesses or connectors.
IPDM E/R
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E13
38
B59
2
Existed
LH
B80
2
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B59
4
Existed
LH
B80
4
LICENSE PLATE LAMP CIRCUIT
EXL-235
< COMPONENT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP CIRCUIT
Component Function Check
INFOID:0000000001099371
NOTE:
Check the tail lamp circuit if the tail lamp and the license plate lamp are not turned ON.
1.
CHECK LICENSE PLATE LAMP OPERATION
IPDM E/R AUTO ACTIVE TEST
1.
Activate IPDM E/R auto active test. Refer to
PCS-9, "Diagnosis Description"
2.
Check that the license plate lamp is turned ON.
CONSULT-III ACTIVE TEST
1.
Select "EXTERNAL LAMP" of IPDM E/R active test item.
2.
With operating the lighting switch, check that the license plate lamp is turned ON.
Is the license plate lamp turned ON?
YES
>> License plate lamp circuit is normal.
NO
>> Refer to
EXL-235, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000001099372
1.
CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect IPDM E/R connector and the license plate lamp connector.
3.
Check continuity between the IPDM E/R harness connector and the license plate lamp harness connec-
tor.
Does continuity exist?
YES
>> GO TO 3.
NO
>> Repair the harnesses or connectors.
3.
CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between the license plate lamp harness connector and the ground.
Does continuity exist?
YES
>> Replace the license plate lamp.
NO
>> Repair the harnesses or connectors.
TAIL
: License plate lamp ON
OFF
: License plate lamp OFF
IPDM E/R
License plate lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E13
38
D185
1
Existed
LH
D184
1
License plate lamp
Ground
Continuity
Connector
Terminal
RH
D185
2
Existed
LH
D184
2
EXL-236
< COMPONENT DIAGNOSIS >
[HALOGEN TYPE]
REAR FOG LAMP CIRCUIT
REAR FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000001099373
1.
CHECK REAR FOG LAMP OPERATION
CONSULT-III ACTIVE TEST
1.
Select "RR FOG LAMP" of BCM (HEAD LAMP) active test item.
2.
With operating the test items, check that the rear fog lamp is turned ON.
Is rear fog lamp turned ON?
YES
>> Rear fog lamp circuit is normal.
NO
>> Refer to
EXL-236, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000001099374
1.
CHECK REAR FOG LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK REAR FOG LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Turn the ignition switch OFF.
2.
Disconnect the rear fog lamp connector.
3.
Turn the ignition switch ON.
4.
Select "RR FOG LAMP" of BCM (HEAD LAMP) active test item.
5.
With operating the test items, check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
3.
CHECK REAR FOG LAMP OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and rear fog lamp harness connector.
Does continuity exist?
YES
>> GO TO 4.
NO
>> Repair the harnesses or connectors.
ON
: Rear fog lamp ON
OFF
: Rear fog lamp OFF
Terminals
Test item
Voltage
(approx.)
(+)
(
−
)
BCM
Ground
RR FOG
LAMP
Connector
Terminal
M66
49
ON
12 V
OFF
0 V
BCM
Rear fog lamp
Continuity
Connector
Terminal
Connector
Terminal
M66
49
B90
1
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст