Nissan Qashqai (2007-2010). Manual — part 853
BLOWER UNIT
VTL-77
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
BLOWER UNIT
Exploded View
INFOID:0000000001093842
Removal and Installation
INFOID:0000000001093843
REMOVAL
1.
Remove Instrument Panel. Refer to
IP-12, "Removal and Installation"
2.
Remove steering member. Refer to
IP-12, "Removal and Installation"
3.
Remove Heater and cooling unit assembly.
4.
Remove harness fixing clip from upper intake box.
5.
Remove door motor harness connector (B).
6.
Remove lower intake box fixing screw from heater and cooling
case.
7.
Remove intake door motor (1).
• Remove fixing screws (A)
• Remove bracket support fixing screws and bracket support
8.
Remove blower motor.Refer to
VTL-79, "Removal and Installa-
CAUTION:
Move blower unit rightward, and remove locating pin (1
part) and joint. Then remove blower unit downward.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
1.
Hi-Level ventilation door unit assem-
bly
2.
Blower motor assembly
3.
Filter cover
4.
In-cabin microfilter
5.
Blower unit
6.
Intake door motor
7.
Intake door unit assembly
E1IIA0002GB
E1IIA0017ZZ
VTL-78
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
BLOWER UNIT
Make sure locating pin (A) are securely inserted.
BLOWER MOTOR
VTL-79
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
BLOWER MOTOR
Exploded View
INFOID:0000000001093844
Removal and Installation
INFOID:0000000001093845
REMOVAL
LHD Model
1.
Remove driver lower instrument panel. Refer to
IP-12, "Removal and Installation"
.
2.
Remove driver foot duct fixing screw, and remove it.
3.
Remove accelerator pedal, and disconnect harness connector. Refer to
4.
Remove brake and clutch pedal assembly, disconnect harness connectors. Refer to
[Brake pedal (LHD)],
BR-61, "Removal and Installation"
[Brake pedal (RHD)],
1.
Hi-Level ventilation door unit assem-
bly
2.
Blower motor assembly
3.
Filter cover
4.
In-cabin microfilter
5.
Blower unit
6.
Intake door motor
7.
Intake door unit assembly
E1IIA0002GB
VTL-80
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
BLOWER MOTOR
5.
Remove blower motor harness connector.
6.
Remove motor fixing screw, then remove blower motor.
7.
Remove blower motor assembly, as shown.
• Remove fixing screw.
• Disconnect harness connector (A).
• Release maintaining pawl (1) then turn counter clockwise (2)
blower motor assembly.
• Pull outside (3) and remove it.
CAUTION:
Take care of harness connectors around blower motor.
RHD Model
1.
Remove passenger lower instrument panel. Refer to
IP-12, "Removal and Installation"
.
2.
Remove Glove Box.
3.
Remove passenger foot duct fixing screw, and remove it.
4.
Remove glove box duct fixing screw, and remove it.
5.
Remove BCM unit. Refer to
BCS-64, "Removal and Installation"
6.
Remove blower motor harness connector.
7.
Remove blower motor assembly, as shown.
8.
Remove fixing screw.
• Disconnect harness connector (A).
• Release maintaining pawl (1) then turn counter clockwise (2)
blower motor assembly.
• Pull outside (3) and remove it.
CAUTION:
Take care of harness connectors around blower motor.
INSTALLATION
Installation is basically the reverse order of removal.
E1IIA0009ZZ
E1IIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст