Nissan Qashqai (2007-2010). Manual — part 1512
LAN
MAIN LINE BETWEEN ABS AND BCM CIRCUIT
LAN-73
< COMPONENT DIAGNOSIS >
[CAN]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MAIN LINE BETWEEN ABS AND BCM CIRCUIT
Diagnosis Procedure
INFOID:0000000000977599
INSPECTION PROCEDURE
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector E105
-
Harness connector M77
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the following harness connectors.
-
ABS actuator and electric unit (control unit)
-
Harness connectors E105 and M77
2.
Check the continuity between the ABS actuator and electric unit (control unit) and the harness connector.
-
Models with ESP
-
Models with ABS
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the ABS actuator and electric unit (control unit) harness connector
and the harness connector E105.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the connector of BCM.
2.
Check the continuity between the harness connector and the BCM harness connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the ABS actuator and electric unit (control
unit) and the BCM.
NO
>> Repair the main line between the harness connector M77 and the BCM.
ABS actuator and electric unit (control unit)
harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E36
26
E105
52
Existed
15
51
Existed
ABS actuator and electric unit (control unit)
harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E34
26
E105
52
Existed
15
51
Existed
Harness connector
BCM harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M77
52
M65
19
Existed
51
20
Existed
LAN-74
< COMPONENT DIAGNOSIS >
[CAN]
MAIN LINE BETWEEN ABS AND TCM CIRCUIT
MAIN LINE BETWEEN ABS AND TCM CIRCUIT
Diagnosis Procedure
INFOID:0000000000968770
INSPECTION PROCEDURE
1.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Disconnect the following harness connectors.
-
ECM
-
ABS actuator and electric unit (control unit)
-
Harness connectors E7 and F121
4.
Check the continuity between the ABS actuator and electric unit (control unit) harness connector and the
harness connector.
-
Models with ESP
-
Models with ABS
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the ABS actuator and electric unit (control
unit) and the harness connector E7.
NO
>> Repair the main line between the ABS actuator and electric unit (control unit) and the TCM.
ABS actuator and electric unit (control unit)
harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E36
26
E7
2
Existed
15
1
Existed
ABS actuator and electric unit (control unit)
harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E34
26
E7
2
Existed
15
1
Existed
LAN
MAIN LINE BETWEEN TCM AND BCM CIRCUIT
LAN-75
< COMPONENT DIAGNOSIS >
[CAN]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MAIN LINE BETWEEN TCM AND BCM CIRCUIT
Diagnosis Procedure
INFOID:0000000000968771
INSPECTION PROCEDURE
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector E105
-
Harness connector M77
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the following harness connectors.
-
Harness connector F121 and E7
-
Harness connector E105 and M77
2.
Check the continuity between the harness connectors.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the harness connectors E7 and E105.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the connector of BCM.
2.
Check the continuity between the harness connector and the BCM harness connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the TCM and the BCM.
NO
>> Repair the main line between the harness connector M77 and the BCM.
Harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E7
2
E105
52
Existed
1
51
Existed
Harness connector
BCM harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M77
52
M65
19
Existed
51
20
Existed
LAN-76
< COMPONENT DIAGNOSIS >
[CAN]
MAIN LINE BETWEEN BCM AND DLC CIRCUIT
MAIN LINE BETWEEN BCM AND DLC CIRCUIT
Diagnosis Procedure
INFOID:0000000000968772
INSPECTION PROCEDURE
1.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Disconnect the following harness connectors.
-
ECM
-
BCM
4.
Check the continuity between the BCM harness connector and the data link connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the BCM and the data link connector.
NO
>> Repair the main line between the BCM and the data link connector.
BCM harness connector
Data link connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M65
19
M4
6
Existed
20
14
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст