Nissan Qashqai (2007-2010). Manual — part 1266
WINDSHIELD GLASS
GW-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Removal and Installation
INFOID:0000000001093975
REMOVAL
1.
Remove the front pillar garnish. Refer to
INT-14, "Removal and Installation"
.
2.
Partially remove the headlining (front edge). Refer to
INT-21, "Removal and Installation"
3.
Remove the cowl top cover. Refer to
EXT-19, "Removal and Installation"
.
4.
Remove the roof side molding. Refer to
EXT-24, "Removal and Installation"
.
5.
Apply protective tape around the windshield glass and sunroof glass to protect the painted surface from
damage.
6.
After removing moldings, remove glass using piano wire or power cutting tool (A) and an inflatable pump
bag (B).
NOTE:
If a windshield glass is to be reused, mark the body and the glass with matching marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
• When a glass is to be reused, do not use a cutting knife or power cutting tool.
• Do not scratch the glass when removing.
• Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
• The dam rubber and insulator should be installed in position.
• Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the manuals furnished
with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger room air pressure when a door is closed.
• The molding must be installed securely so that it is in position and leaves no gap.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the windshield in case of an accident.
CAUTION:
• Perform adjustment of front wiper stop location. Refer to
.
1.
Windshield glass
2.
Dam rubber
3.
Windshield molding
4.
Spacer
5.
Rain sensor bracket
6.
Mirror base
7.
Adhesive
8.
Primer
9.
Roof panel
10. Roof glass
11.
Body side outer panel
12. Cowl top
13. Cowl top cover
Refer to
PIIB5779E
GW-12
< ON-VEHICLE REPAIR >
WINDSHIELD GLASS
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time will increase
under lower temperature and lower humidity.
Inspection
INFOID:0000000001093976
Repairing Water Leakage for Windshield
Leakage can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the windshield area while pushing glass outward.
To stop the leakage, apply primer (if necessary) and then urethane adhesive to the leakage point.
SUNROOF
GW-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
SUNROOF
Exploded View
INFOID:0000000001094000
1.
Sunroof glass
2.
Sunroof molding
3.
Dam rubber
4.
Spacer
5.
Adhesive
6.
Primer
7.
Windshield glass
8.
Windshield molding
9.
Front roof rail upper
JMKIA0466GB
GW-14
< ON-VEHICLE REPAIR >
SUNROOF
Removal and Installation
INFOID:0000000001094004
REMOVAL
1.
Remove the headlining.Refer to
INT-21, "Removal and Installation"
2.
Remove the sunshade unit assembly. Refer to
RF-53, "SUNSHADE UNIT ASSEMBLY : Removal and
.
3.
Remove the clips on sunroof inner finisher, and remove the sunroof inner finisher.
4.
Remove the roof side molding. Refer to
EXT-24, "Removal and Installation"
.
5.
Remove the windshield molding. Refer to
GW-11, "Removal and Installation"
.
6.
Apply protective tape around the sunroof glass and windshield glass and panel to protect from damage.
7.
Cut the sunroof moldings with the cutting knife.
8.
Remove the sunroof moldings using pliers, remove sunroof glass using piano wire or power cutting tool
and an inflatable pump bag.
NOTE:
If a glass is to be reused, mark the body and the glass with matching marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
• When a glass is to be reused, do not use a cutting knife or power cutting tool.
• Do not scratch the glass when removing.
• Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
• The dam rubber and insulator should be installed in position.
• Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the manuals furnished
with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger room air pressure when a door is closed.
• The molding must be installed securely so that it is in position and leaves no gap.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the windshield in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time will increase
under lower temperature and lower humidity.
10. Body side outer panel
11.
Roof side molding
12. Roof panel
Refer to
for symbols in the figure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст