Nissan Qashqai (2007-2010). Manual — part 513
CLUTCH FLUID
CL-7
< ON-VEHICLE MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
• RS6F94R and RS6F52A
CAUTION:
Hold it to prevent releasing clutch tube from bleeding con-
nector when fluid pressure is applied in the tube.
5.
Slide clutch tube (1) in the direction of the arrow as shown in the figure.
• RS5F92R
• RS6F94R and RS6F52A
6.
Depress the clutch pedal soon and hold it, and then bleed the air
from the piping.
CAUTION:
Hold it to prevent releasing clutch tube from bleeding con-
nector when fluid pressure is applied in the tube.
7.
Return clutch tube (1) and lock pin to their original positions.
8.
Release clutch pedal and wait for 5 seconds.
9.
Repeat steps 3 to 8 until no bubbles are observed in the clutch fluid.
JPDIB0041ZZ
Dimension “A”
: 5 mm (0.20 in)
JPDIB0045ZZ
2
: Clutch housing
Dimension “A”
: 10 mm (0.39 in)
JPDIB0042ZZ
CL-8
< ON-VEHICLE REPAIR >
CLUTCH PEDAL
ON-VEHICLE REPAIR
CLUTCH PEDAL
Exploded View
INFOID:0000000001043511
Removal and Installation
INFOID:0000000001043512
REMOVAL
1.
Remove front kicking plate inner and dash side finisher. Refer to
INT-14, "Removal and Installation"
.
2.
Remove lower instrument panel, driver side. Refer to
IP-12, "Removal and Installation"
3.
Disconnect ASCD clutch switch harness connector and then disconnect clip of harness from clutch pedal
assembly.
4.
Remove master cylinder rod end from clutch pedal assembly.
5.
Remove clutch pedal assembly.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000001043513
1.
Clutch pedal assembly
2.
ASCD clutch switch
3.
Pedal pad
Refer to
for the symbols in the figure.
JPDIB0034GB
PCIB1491E
CLUTCH PEDAL
CL-9
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
INSPECTION AFTER REMOVAL
Check clutch pedal for bend, damage, or a cracked weld. If bend, damage, or a cracked weld is found, replace
clutch pedal assembly.
CL-10
< ON-VEHICLE REPAIR >
CLUTCH MASTER CYLINDER
CLUTCH MASTER CYLINDER
Exploded View
INFOID:0000000001043514
Removal and Installation
INFOID:0000000001043515
REMOVAL
CAUTION:
• Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
• Never disassemble master cylinder.
1.
Remove the air cleaner case and air duct (inlet) or air ducts. Refer to
EM-27, "Removal and Installation"
EM-144, "Removal and Installation"
EM-265, "Removal and Installation"
2.
Remove the battery. Refer to
PG-118, "Removal and Installation"
.
3.
Disconnect the connectors (A) and then remove the bracket (1).
4.
Drain clutch fluid in reservoir tank assembly and then remove
hose.
5.
Remove master cylinder rod end from clutch pedal assembly.
1.
Reservoir tank assembly
2.
Hose
3.
Master cylinder assembly
JPDIB0035ZZ
JPDIA0240ZZ
PCIB1491E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст