Nissan Qashqai (2007-2010). Manual — part 558
MAINSHAFT AND GEAR
TM-167
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
17. Press in mainshaft rear bearing using the drifts.
18. Install mainshaft C-rings onto mainshaft and check that end play
of mainshaft rear bearing satisfies the standard value.
• If measurement is outside the standard range, reselect main-
shaft C-rings.
19. Install C-ring holder and then install snap ring.
CAUTION:
Never reuse snap ring.
20. Check end play of 1st and 2nd main gears.
Inspection
INFOID:0000000001034962
MAINSHAFT AND GEAR
SCIA0978E
End play standard value
: Refer to
SCIA0979E
PCIB0805E
End play standard value
: Refer to
.
SCIA0973E
TM-168
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
MAINSHAFT AND GEAR
Check items below. If necessary, replace them with new ones.
• Damage, peeling, dent, uneven wear, bending, and other non-
standard conditions of the shaft.
• Excessive wear, damage, peeling, and other non-standard condi-
tions of the gears.
SYNCHRONIZER
Synchronizer Hub and Coupling Sleeve
Check items below. If necessary, replace them with new ones.
• Damage and unusual wear on contact surfaces of coupling sleeve,
synchronizer hub and shifting insert.
• Coupling sleeve and synchronizer hub must move smoothly.
Baulk Ring and Spread Spring
Check items below. If necessary, replace them with new ones.
• If any crack, damage, or excessive wear is found on cam face of
baulk ring or working face of insert, replace it.
Baulk Ring Clearance for Double Cone Synchronizer (1st)
Check the clearance between outer baulk ring, synchronizer cone,
and inner baulk ring as follows.
CAUTION:
The clearances “A” and “B” are controlled with outer baulk
ring, synchronizer cone, and inner baulk ring as a set. Replace
them as a set if the clearances are outside the limit value.
SCIA1076J
SMT387A
SMT867D
SCIA0950E
MAINSHAFT AND GEAR
TM-169
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Measure the clearance “A” at 2 points or more diagonally oppo-
site using a dial indicator. And then calculate mean value.
2.
Measure the clearance “B” at 2 points or more diagonally oppo-
site using a feeler gauge. And then calculate mean value.
Baulk Ring Clearance for Triple Cone Synchronizer (2nd)
Check the clearance between outer baulk ring, synchronizer cone,
and inner baulk ring as follows.
CAUTION:
The clearances “A”, “B”, and “C” are controlled with outer
baulk ring, synchronizer cone, and inner baulk ring as a set.
Replace them as a set if the clearances are outside the limit
value.
1.
Measure the clearance “A” at 2 points or more diagonally oppo-
site using a feeler gauge (B) when pressing outer baulk ring (1),
synchronizer cone (2), and inner baulk ring (3) toward gear taper
cone (C). And then calculate mean value.
Clearance “A”
Standard value
: Refer to
.
Limit value
: Refer to
.
SCIA0951E
Clearance “B”
Standard value
: Refer to
.
Limit value
: Refer to
.
SCIA1084E
PCIB1358E
Clearance “A”
Standard value
: Refer to
Limit value
: Refer to
JPDIC0034ZZ
TM-170
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
MAINSHAFT AND GEAR
2.
Measure the clearance “B” at 2 points or more diagonally oppo-
site using a feeler gauge. And then calculate mean value.
3.
Measure the clearance “C” at 2 points or more diagonally oppo-
site using a feeler gauge (A) when pressing outer baulk ring (1),
synchronizer cone (2), and inner baulk ring (3) toward gear taper
cone (B). And then calculate mean value.
BEARING
Check items below. If necessary, replace them with new ones.
• Damage and rough rotation of bearing
Clearance “B”
Standard value
: Refer to
.
Limit value
: Refer to
.
PCIB1360E
Clearance “C”
Standard value
: Refer to
Limit value
: Refer to
JPDIC0035ZZ
MTF0041D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст