Nissan Qashqai (2007-2010). Manual — part 635
SERVICE DATA AND SPECIFICATIONS (SDS)
DLN-113
< SERVICE DATA AND SPECIFICATIONS (SDS)
[REAR PROPELLER SHAFT: 3F SPL18-DOJ75]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000000972156
Propeller Shaft Runout
INFOID:0000000000972157
Unit: mm (in)
Journal Axial Play
INFOID:0000000000972158
Unit: mm (in)
Applied model
4WD
MR20DE
M/T
CVT
Propeller shaft model
3F SPL18-DOJ75
Number of joints
3
Type of journal bearings
(Non-disassembly type)
1st joint
Shell type
2nd joint
Cardan type
3rd joint
Shell type
Coupling method with transfer
Flange type
Coupling method with rear final drive
Flange type
Shaft length
1st (Spider to cardan joint center)
1091 mm (42.95 in)
2nd (Cardan joint center to spider)
831 mm (32.72 in)
Shaft outer diameter
1st
57 mm (2.24 in)
2nd
70 mm (2.76 in)
Item
Limit
Propeller shaft runout
0.6 (0.024)
Item
Standard
Journal axial play
0 (0)
DLN-114
< SYMPTOM DIAGNOSIS >
[REAR FINAL DRIVE: R145]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000000972159
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
NVH in DLN section
NVH in F
AX,
RAX, FSU and
R
S
U sections
NVH in WT section
NVH in WT section
NVH i
n
F
AX and RAX
secti
o
n
NVH in B
R
section
NVH in S
T
section
Possible cause and SUSPECTED PARTS
Gea
r to
ot
h ro
ug
h
Ge
ar co
nt
a
c
t im
pro
p
e
r
T
o
o
th su
rfac
es
wo
rn
Ba
ck
la
sh
in
co
rrec
t
Com
p
ani
on
fl
an
ge
ex
ce
ss
iv
e
run
o
u
t
Ge
ar oi
l im
pro
p
e
r
PROPELLER S
H
AFT
AXLE AND S
U
S
PENSION
TI
RE
S
ROAD WHEE
L
DRIVE SHAFT
BRAKE
S
STE
E
RING
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
PRECAUTIONS
DLN-115
< PRECAUTION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PRECAUTION
PRECAUTIONS
Service Notice or Precautions for Rear Final Drive
INFOID:0000000000972160
CAUTION:
• Check for the correct installation status prior to removal or disassembly. If matching marks are
required, be certain they do not interfere with the function of the parts when applied.
• Overhaul should be done in a clean work area, it is preferable to work in dustproof area.
• Before disassembly, using steam or white gasoline, completely remove sand and mud from the exte-
rior of the unit, preventing them from entering into the unit during disassembly or assembly.
• Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace
them with a new one if necessary.
• Gaskets, seals and O-rings should be replaced any time when the unit is disassembled.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to out-
side. If tightening sequence is specified, observe it.
• Clean and flush the parts sufficiently and blow-dry them.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mounting surface; then remove any mois-
ture, oil, and foreign materials from the application and mounting surfaces.
• Always use shop paper for cleaning the inside of components.
• Avoid using cotton gloves or shop rags to prevent entering of lint.
• During assembly, observe the specified tightening torque, and apply new gear oil, petroleum jelly, or
multi-purpose grease as specified for each vehicle, if necessary.
DLN-116
< PREPARATION >
[REAR FINAL DRIVE: R145]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000000972161
Tool number
Tool name
Description
KV38100200
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
• Installing front oil seal
• Installing side oil seal
ST27861000
Drift
a: 62 mm (2.44 in) dia.
b: 52 mm (2.05 in) dia.
Installing front oil seal
ST35271000
Drift
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.
Installing center oil seal
ST22360002
Drift
a: 29 mm (1.14 in) dia.
b: 23 mm (0.91 in) dia.
c: 150 mm (5.91 in)
Installing coupling front bearing
ST33052000
Drift
a: 22 mm (0.87 in) dia.
b: 28 mm (1.10 in) dia.
Removing side bearing inner race
KV38108400
Pinion nut wrench
Removing and installing drive pinion nut
ZZA1143D
ZZA0832D
ZZA0814D
ZZA0546D
ZZA1023D
ZZA1206D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст