Nissan Qashqai (2007-2010). Manual — part 1938
AV-10
< COMPONENT DIAGNOSIS >
[AUDIO WITHOUT NAVIGATION]
MICROPHONE SIGNAL CIRCUIT
MICROPHONE SIGNAL CIRCUIT
Description
INFOID:0000000000996424
Supply power from audio unit to microphone. The microphone transmits the sound voice to the audio unit.
Diagnosis Procedure
INFOID:0000000000996425
1.
CHECK CONTINUITY BETWEEN AUDIO UNIT AND MICROPHONE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect audio unit connector and microphone connector.
3.
Check continuity between audio unit harness connector terminals 35, 36, 37 and microphone harness
connector terminals 1, 2, 4.
4.
Check continuity between audio unit harness connector terminals 35, 37 and ground.
Is inspection result OK?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK VOLTAGE MICROPHONE VCC
1.
Connect audio unit connector.
2.
Turn ignition switch ON.
3.
Check voltage between audio unit harness connector terminal 37 and ground.
Is inspection result OK?
YES
>> GO TO 3.
NO
>> Replace audio unit.
3.
CHECK MICROPHONE SIGNAL
1.
Connect microphone connector.
2.
Check signal between audio unit harness connector terminals 35 and 36.
Is inspection result OK?
YES
>> Replace audio unit.
NO
>> Replace microphone.
35 - 1
: Continuity should exist.
36 - 2
: Continuity should exist.
37 - 4
: Continuity should exist.
35, 37 - Ground
: Continuity should not exist.
37 - ground
: Approx. 5 V
35 - 36
PKIB5037J
AV
STEERING SWITCH SIGNAL A CIRCUIT
AV-11
< COMPONENT DIAGNOSIS >
[AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
STEERING SWITCH SIGNAL A CIRCUIT
Description
INFOID:0000000000996436
Transmits the steering switch signal to audio unit.
Diagnosis Procedure
INFOID:0000000000996437
1.
CHECK STEERING SWITCH SIGNAL A CIRCUIT
1.
Disconnect audio unit connector and spiral cable connector.
2.
Check continuity between audio unit harness connector terminal 6 and spiral cable harness connector ter-
minal 24.
3.
Check continuity between audio unit harness connector terminal 6 and ground.
Is inspection result OK?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES
>> GO TO 3.
NO
>> Replace spiral cable.
3.
CHECK AUDIO UNIT VOLTAGE
1.
Connect audio unit connector and spiral cable connector.
2.
Turn ignition switch ON.
3.
Check voltage between audio unit harness connector terminals 6 and 15.
Is inspection result OK?
YES
>> GO TO 4.
NO
>> Replace audio unit.
4.
CHECK STEERING SWITCH
1.
Turn ignition switch OFF.
2.
Check steering switch. Refer to
.
Is inspection result OK?
YES
>> INSPECTION END
NO
>> Replace steering switch.
Component Inspection
INFOID:0000000000996438
Measure the resistance between the steering switch connector terminals 20 to 17 and 16 to 17.
6 - 24
: Continuity should exist.
6 - Ground
: Continuity should not exist.
6 - 15
: Approx. 5 V
AV-12
< COMPONENT DIAGNOSIS >
[AUDIO WITHOUT NAVIGATION]
STEERING SWITCH SIGNAL A CIRCUIT
Standard
Between terminals 20 and 17
VOL UP switch ON
: 634 – 665
Ω
SEEK UP switch ON
: 162 – 168
Ω
SOURCE switch ON
: 0
Ω
Between terminals 16 and 17
VOL DOWN switch ON
: 634 – 665
Ω
SEEK DOWN switch ON
: 162 – 168
Ω
switch ON
: 0
Ω
JPNIA0167GB
AV
STEERING SWITCH SIGNAL B CIRCUIT
AV-13
< COMPONENT DIAGNOSIS >
[AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
STEERING SWITCH SIGNAL B CIRCUIT
Description
INFOID:0000000000999575
Transmits the steering switch signal to audio unit.
Diagnosis Procedure
INFOID:0000000000996441
1.
CHECK STEERING SWITCH SIGNAL B CIRCUIT
1.
Disconnect audio unit connector and spiral cable connector.
2.
Check continuity between audio unit harness connector terminal 16 and spiral cable harness connector
terminals 32.
3.
Check continuity between audio unit harness connector terminal 16 and ground.
Is inspection result OK?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES
>> GO TO 3.
NO
>> Replace spiral cable.
3.
CHECK AUDIO UNIT VOLTAGE
1.
Connect audio unit connector and spiral cable connector.
2.
Turn ignition switch ON.
3.
Check voltage between audio unit harness connector terminals 16 and 15.
Is inspection result OK?
YES
>> GO TO 4.
NO
>> Replace audio unit.
4.
CHECK STEERING SWITCH
1.
Turn ignition switch OFF.
2.
Check steering switch. Refer to
.
Is inspection result OK?
YES
>> INSPECTION END
NO
>> Replace steering switch.
Component Inspection
INFOID:0000000000999577
Measure the resistance between the steering switch connector terminals 20 to 17 and 16 to 17.
16 - 32
: Continuity should exist.
16 - Ground
: Continuity should not exist.
16 - 15
: Approx. 5 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст