Nissan Qashqai (2007-2010). Manual — part 1953

AV-70

< FUNCTION DIAGNOSIS >

[AUDIO WITH NAVIGATION]

DIAGNOSIS SYSTEM (CAMERA CONTROL UNIT)

DIAGNOSIS SYSTEM (CAMERA CONTROL UNIT)

CONSULT-III Function (REAR VIEW CAMERA)

INFOID:0000000001096711

CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.

WORK SUPPORT

For details, refer to Refer to Service Manual.

DATA MONITOR

Diagnosis part

Check Item,

Diagnosis Mode

Description

REAR VIEW CAMERA

WORK SUPPORT

Adjusts the vehicle width and distance guiding lines that overlap camera image.

DATA MONITOR

Displays input data for rear view camera control unit in real-time.

ECU PART NUMBER

Displays rear view camera control unit part number.

Work item

Description

SELECT GUIDELINE PATTERN

The opening of the vehicle width and distance guiding lines can be selected from 2 patterns.

ADJ GUIDELINE POSITION

Adjusts the vehicle width and distance guiding lines upper/lower/left/right.

Monitor item

Content

R POSI SIG [ON/OFF]

“ON (selector lever R position)/OFF (other than R position)” status as judged from the reverse
signal is displayed.

AV

U1000 CAN COMM CIRCUIT

AV-71

< COMPONENT DIAGNOSIS >

[AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

COMPONENT DIAGNOSIS

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000000947021

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to

LAN-59, "CAN Communication Signal Chart"

.

DTC Logic

INFOID:0000000000947022

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000000947023

1.

PERFORM SELF DIAGNOSTIC

1.

Turn ignition switch ON and wait for 2 second or more.

2.

Check “Self Diagnostic Result” of “MULTI AV”.

Is “CAN COMM CIRCUIT” displayed?

YES

>> Refer to “LAN system”. Refer to

LAN-46, "Trouble Diagnosis Flow Chart"

.

NO

>> Refer to GI section. Refer to

GI-39, "Intermittent Incident"

.

DTC

Display contents of CON-

SULT-III

Diagnostic item is detected when...

Probable malfunction location

U1000

CAN COMM CIRCUIT
[U1000]

NAVI control unit does not transmit or receive
CAN communication signal for 2 seconds or
more.

CAN communication system

AV-72

< COMPONENT DIAGNOSIS >

[AUDIO WITH NAVIGATION]

U1010 CONTROL UNIT (CAN)

U1010 CONTROL UNIT (CAN)

Description

INFOID:0000000000947024

Initial diagnosis of NAVI control unit.

DTC Logic

INFOID:0000000000947025

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000000947026

1.

REPLACE NAVI CONTROL UNIT

Replace NAVI control unit when DTC U1010 is detected.

>> INSPECTION END

DTC

Display contents of CON-

SULT-III

Diagnostic item is detected when...

Probable malfunction location

U1010

CONTROL UNIT (CAN)
[U1010]

CAN initial diagnosis malfunction is detected.

NAVI control unit

AV

U1310 NAVI CONTROL UNIT

AV-73

< COMPONENT DIAGNOSIS >

[AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

U1310 NAVI CONTROL UNIT

Description

INFOID:0000000000947027

Replace the NAVI control unit if this DTC is displayed. Refer to

AV-201, "Exploded View"

.

DTC Logic

INFOID:0000000000947028

Part name

Description

NAVI CONTORL UNIT

• Map data can be read from the map DVD-ROM by installing map DVD-ROM.
• It is the master unit of the MULTI AV system, and it is connected to each control

unit by means of communication. It operates each system according to com-
munication signals from the NAVI control unit.

• The NAVI control unit includes the audio, hands-free phone, navigation, and

vehicle information functions.

• It is connected to ECM and combination meter via CAN communication to ob-

tain necessary information for the vehicle information function.

• It inputs the illumination signals that are required for the display dimming con-

trol.

• It inputs the signals for driving status recognition (vehicle speed, reverse and

parking brake).

DTC

Display contents of

CONSULT-III

DTC Detection Condition

Action to take

U1310

CONTROL UNIT (AV)
[U1310]

An initial diagnosis error is detected in AV communication
circuit.

Replace NAVI control unit.