Nissan Qashqai (2007-2010). Manual — part 773
SR-4
< ON-VEHICLE REPAIR >
DRIVER AIR BAG MODULE
ON-VEHICLE REPAIR
DRIVER AIR BAG MODULE
Exploded View
INFOID:0000000001069721
Removal and Installation
INFOID:0000000001069722
REMOVAL
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at
least 3 minutes.
• Always work from the side of air bag module. Do not work in front of it.
• Do not use air tools or electric tools for servicing.
1.
Locate retaining clip access hole (left/right) and insert screw-
driver (A).
2.
Press upward on retaining clip (1) until driver air bag module is
released from steering wheel.
3.
Lift the driver air bag module from the steering wheel.
JMHIA0189ZZ
1.
Steering wheel
2.
Driver air bag module
3.
Steering switch
JMHIA0190ZZ
JMHIA0224ZZ
DRIVER AIR BAG MODULE
SR-5
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
4.
Disconnect the driver air bag module and horn connectors, then remove the driver air bag module.
NOTE:
• For installing/removing driver air bag module connector, insert
thin screwdriver wrapped in tape into notch, lift lock and
remove connector.
• Install connector with lohe k raised, and push lock into connec-
tor.
• After installing the connector, check that the lock is pushed
securely into it.
CAUTION:
• Always place air bag module with pad side facing upward.
• Do not insert any foreign objects (screwdriver, etc.) into air
bag module.
• Do not disassemble air bag module.
• Do not expose the air bag module to temperatures exceeding
90
°
C (194
°
F).
• Do not allow oil, grease or water to come in contact with the
air bag module.
• Replace the air bag module if it has been dropped or sus-
tained an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Do not damage the harness while installing.
• In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function
and delete the memory by CONSULT-III.
• In case that malfunction is still detected after the above operations, perform self-diagnosis to repair
malfunctions.
• After the work is completed, check that no malfunctioning system is detected by air bag warning
lamp. Refer to
SRC-10, "Diagnosis Description"
.
PHIA0953J
: Upward
JMHIA0191ZZ
JMHIA0009ZZ
SR-6
< ON-VEHICLE REPAIR >
SPIRAL CABLE
SPIRAL CABLE
Exploded View
INFOID:0000000001069723
Removal and Installation
INFOID:0000000001069724
REMOVAL
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes.
• Do not use air tools or electric tools for servicing.
1.
Remove the driver air bag module. Refer to
SR-4, "Removal and Installation"
2.
Remove the steering wheel. Refer to
ST-9, "Removal and Installation"
3.
Remove the column cover (upper/lower). Refer to
4.
Disconnect spiral cable body side connectors (A).
NOTE:
Disconnect spiral cable body side connectors after remove the
spiral cable.
5.
Remove spiral cable fixing screws, and pawls (left/right).
6.
Pull out forward the spiral cable.
CAUTION:
• Do not disassemble the spiral cable.
• Do not apply lubricant to the spiral cable.
• Do not allow oil, grease, detergent or water to come in contact with the spiral cable.
JMHIA0193ZZ
1.
Spiral cable
2.
Steering wheel
3.
Driver air bag module harness con-
nectors
4.
Steering column assembly
5.
Steering column cover (lower)
6.
Steering lock escation
7.
Steering column cover (upper)
JMHIA0194ZZ
SPIRAL CABLE
SR-7
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Do not make an impact the spiral cable by dropping etc.
Replace the spiral cable if it has been dropped or sustained
an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• The spiral cable may snap by steering operation if the cable is
installed in an improper position.
• The neutral position is set as follows.
• Turn carefully the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and half turns) and
stop turning at the point (B) on which the stopper insertion
holes are in the same position.
• The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper is
removed.
• Do not over turn spiral cable or beyond number of turns
required. (These will cause cable snap.)
• Adjust the spiral cable locating pin (A) to the steering wheel
locating pin hole (C).
• Secure the air bag harness with the harness fixing hook.
• In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function
and delete the memory by CONSULT-III.
• In case that malfunction is still detected after the above operations, perform self-diagnosis to repair
malfunctions.
• After the work is completed, check that no malfunctioning system is detected by air bag warning
lamp. Refer to
SRC-10, "Diagnosis Description"
.
JMHIA0009ZZ
JMHIA0013ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст