Nissan Qashqai (2007-2010). Manual — part 677
PREPARATION
BR-7
< PREPARATION >
[LHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000000925766
Tool name
Description
Pin punch
a: 4 mm (0.16 in) dia.
Removing and installing reservoir tank
pin
NT410
BR-8
< ON-VEHICLE MAINTENANCE >
[LHD]
BRAKE PEDAL
ON-VEHICLE MAINTENANCE
BRAKE PEDAL
Exploded View
INFOID:0000000000925771
.
Inspection and Adjustment
INFOID:0000000000925772
INSPECTION
Brake Pedal Height
Check the height (H
1
) between the accelerator pedal stopper (1) and
the brake pedal upper surface.
CAUTION:
Remove the floor trim.
ASCD Cancel Switch and Stop Lamp Switch
Check the clearance (C) among bracket (1) and ASCD cancel
switch/stop lamp switch (2) threaded end.
CAUTION:
The stop lamp must be turned off when the brake pedal is
released.
NOTE:
Pull the brake pedal pad to make the clearance between bracket and ASCD cancel switch/stop lamp switch
threaded end.
Brake Pedal Play
Press the brake pedal. Check the brake pedal play (A).
Depressed Brake Pedal Height
Standard
Brake pedal height (H
1
)
: Refer to
.
JPFIA0119ZZ
Standard
Clearance (C) between
bracket and ASCD cancel
switch/stop lamp switch
threaded end
: Refer to
.
JPFIA0074ZZ
Standard
Pedal play (A)
: Refer to
.
JPFIA0121ZZ
BRAKE PEDAL
BR-9
< ON-VEHICLE MAINTENANCE >
[LHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Check the height between the accelerator pedal stopper (1) and the
brake pedal upper surface (H
2
) when depressing the brake pedal at
490 N (50 kg, 110 lb) while turning engine ON.
CAUTION:
Remove the floor trim.
ADJUSTMENT
Brake Pedal Height
1.
Disconnect the harness connector from ASCD cancel switch and stop lamp switch.
2.
Turn the ASCD cancel switch and stop lamp switch 45
°
counterclockwise.
3.
Loosen the input rod lock nut (1). Adjust the brake pedal to the
specification. Tighten the input rod lock nut to the specification.
Refer to
.
CAUTION:
The threaded end of the input rod (2) must project to the
inner side (L) of the clevis (3).
ASCD Cancel Switch and Stop Lamp Switch
1.
Disconnect the harness connector from ASCD cancel switch and stop lamp switch.
2.
Turn the ASCD cancel switch and stop lamp switch 45
°
counterclockwise.
3.
Press-fit ASCD cancel switch/stop lamp switch (2) until ASCD
cancel switch/stop lamp switch hits the bracket (1) 45
°
clock-
wise.
CAUTION:
• The clearance (C) between the bracket and ASCD cancel
switch/stop lamp switch threaded end must be the speci-
fied value. Refer to
.
• The stop lamp must be turned off when the brake pedal is
released.
Brake Pedal Play
1.
Disconnect the harness connector from ASCD cancel switch and stop lamp switch.
2.
Turn the ASCD cancel switch and stop lamp switch 45
°
counterclockwise.
Standard
Depressed brake pedal
height (H
2
)
: Refer to
JPFIA0120ZZ
JPFIA0003ZZ
Standard
Brake pedal height (H
1
)
: Refer to
JPFIA0119ZZ
JPFIA0074ZZ
BR-10
< ON-VEHICLE MAINTENANCE >
[LHD]
BRAKE PEDAL
3.
Press-fit ASCD cancel switch/stop lamp switch (2) until ASCD
cancel switch/stop lamp switch hits the bracket (1) 45
°
clock-
wise.
CAUTION:
• The clearance (C) between the bracket and ASCD cancel
switch/stop lamp switch threaded end must be the speci-
fied value. Refer to
.
• The stop lamp must be turned off when the brake pedal is
released.
JPFIA0074ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст