Nissan Qashqai (2007-2010). Manual — part 449
POWER SUPPLY AND GROUND CIRCUIT
EC-1315
< COMPONENT DIAGNOSIS >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair open circuit or short to ground or short power in harness or connectors.
11.
CHECK 20A FUSE
1.
Disconnect 20A fuse (No. 52) from IPDM E/R.
2.
Check 20A fuse.
Is the inspection result normal?
YES
>> GO TO 14.
NO
>> Replace 20A fuse.
12.
CHECK GROUND CONNECTION-II
1.
Turn ignition switch OFF.
2.
Check ground connection E9. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Repair or replace ground connection.
13.
CHECK ECM GROUND CIRCUIT FOR OPEN AND SHORT-II
1.
Disconnect ECM harness connector.
2.
Check the continuity between ECM harness connector and ground.
3.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 14.
NO
>> Repair open circuit or short power in harness or connectors.
14.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair open circuit or short to power in harness or connectors.
ECM
Ground
Continuity
Connector
Terminal
E60
123
Ground
Existed
124
125
128
EC-1316
< COMPONENT DIAGNOSIS >
[K9K]
P0001 FUEL PUMP
P0001 FUEL PUMP
DTC Logic
INFOID:0000000001115046
DTC DETECTION LOGIC
NOTE:
• Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC becomes present after the engine is started.
• If the DTC is present:
- Malfunction indicator (Red) lights up.
Diagnosis Procedure
INFOID:0000000001034174
1.
CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE) POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect high pressure supply pump (volumetric control valve) harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between high pressure supply pump (volumetric control valve) harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connector E7, F121
• Harness for open or short between ECM and high pressure supply pump (volumetric control valve)
• Harness for open or short between IPDM E/R and high pressure supply pump (volumetric control valve)
>> Repair open circuit or short to ground or short to power in harness or connectors.
3.
CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE) OUTPUT SIGNAL CIR-
CUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between high pressure supply pump (volumetric control valve) harness connector
and ECM harness connector.
4.
Also check harness for short to ground and short to power.
DTC No.
Trouble diagnosis name
Possible cause
P0001
HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)
CIRCUIT
• CO: Open circuit
• CO.0: Short circuit to ground
• CC.1: Short circuit to +12V
• 1.DEF: Parameter at maximum level
• Harness or connectors
[High pressure supply pump (volumetric
control valve) circuit is open or shorted.]
• High pressure supply pump (volumetric
control valve)
• Fuel line
High pressure supply pump
(volumetric control valve)
Ground
Voltage
Connector
Terminal
F106
1
Ground
Battery voltage
High pressure supply pump
(volumetric control valve)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F106
2
F68
50
Existed
P0001 FUEL PUMP
EC-1317
< COMPONENT DIAGNOSIS >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)
EC-1321, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace high pressure supply pump.
5.
CHECK FUEL LINE
Check fuel line cleanliness.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Fuel line cleanliness.
6.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000001034175
1.
CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)
1.
Turn ignition switch OFF.
2.
Disconnect high pressure supply pump (volumetric control valve) harness connector.
3.
Check resistance between high pressure supply pump (volumetric control valve) terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace high pressure supply pump.
Terminals
Resistance
1 and 2
1.5 - 15
Ω
EC-1318
< COMPONENT DIAGNOSIS >
[K9K]
P0002 FUEL PUMP
P0002 FUEL PUMP
DTC Logic
INFOID:0000000001115051
DTC DETECTION LOGIC
NOTE:
• Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC is declared present when after the engine is started or following a load test.
Diagnosis Procedure
INFOID:0000000001034260
1.
CHECK LOW PRESSURE FUEL SUPPLY SYSTEM
EC-1262, "BASIC INSPECTION : Special Repair Requirement (TEST 1: Low Pressure Fuel Supply
.
Is the inspection result normal?
OK
>> GO TO 2.
NG
>> Replace or replace. Then GO TO 9.
2.
CHECK INTERNAL FUEL TRANSFER PUMP
Refer to
EC-1263, "BASIC INSPECTION : Special Repair Requirement (TEST 2: Internal Fuel Transfer Pump
Is the inspection result normal?
OK
>> GO TO 3.
NG
>> Replace or replace. Then GO TO 9.
3.
CHECK HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE)
EC-1263, "BASIC INSPECTION : Special Repair Requirement [TEST 3: High Pressure Supply Pump
(Pressure Control Valve) Check]"
Is the inspection result normal?
OK
>> GO TO 4.
NG
>> Replace or replace. Then GO TO 9.
4.
CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)
EC-1264, "BASIC INSPECTION : Special Repair Requirement [TEST 4: High Pressure Supply Pump
(Volumetric Control Valve) Check]"
.
Is the inspection result normal?
OK
>> GO TO 5.
NG
>> Replace or replace. Then GO TO 9.
5.
CHECK RAIL HIGH PRESSURE REGULATION
EC-1267, "BASIC INSPECTION : Special Repair Requirement (TEST 5: Rail High Pressure Regula-
.
Is the inspection result normal?
OK
>> GO TO 6.
NG
>> Replace or replace. Then GO TO 9.
6.
CHECK MAJOR LEAK IN FUEL INJECTORS/FUEL INJECTORS OPEN
DTC No.
Trouble diagnosis name
Possible cause
P0002
HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)
ADAPTIVE
• 1.DEF: Parameter at maximum stop
• 2.DEF: Parameter at maximum level
• Harness or connectors
[High pressure supply pump (volumetric
control valve) circuit is open or shorted.]
(Fuel rail pressure sensor circuit is open or
shorted.)
• High pressure supply pump (volumetric
control valve)
• Fuel rail pressure sensor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст