Nissan Qashqai (2007-2010). Manual — part 21
EM-32
< ON-VEHICLE REPAIR >
[HR16DE]
EXHAUST MANIFOLD
EXHAUST MANIFOLD
Exploded View
INFOID:0000000000893847
Removal and Installation
INFOID:0000000000894021
REMOVAL
1.
Remove exhaust front tube. Refer to
2.
Remove the harness bracket of heated oxygen sensor 1 from the cylinder head.
3.
Remove exhaust manifold cover.
4.
Remove the heated oxygen sensor 1.
1.
Exhaust manifold cover
2.
Exhaust manifold cover
3.
Harness bracket
4.
Heated oxygen sensor 1
5.
Exhaust manifold stay
6.
Exhaust manifold
7.
Gasket
8.
Stud bolt
9.
Heat insulator
: Engine front
Refer to
for symbols in the figure.
PBIC4750E
EXHAUST MANIFOLD
EM-33
< ON-VEHICLE REPAIR >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Using heated oxygen sensor wrench [SST: KV10117100] (A),
remove heated oxygen sensor 1.
CAUTION:
Handle heated oxygen sensor 1 carefully and avoid
impacts.
NOTE:
The exhaust manifold can be removed and installed without
removing the heated oxygen sensor 1 (Disassembly of harness
connector is necessary).
5.
Remove exhaust manifold side mounting bolt of exhaust manifold stay.
6.
Remove exhaust manifold.
• Loosen nuts in the reverse of the order shown in the figure.
7.
Remove gasket.
CAUTION:
Cover engine openings to avoid entry of foreign materials.
8.
Remove exhaust manifold cover from back of exhaust manifold.
INSTALLATION
Note the following, and install in the reverse order of removal.
Exhaust Manifold
1.
Tighten nuts in numerical order shown in the figure.
2.
Tighten to the specified torque again.
Inspection
INFOID:0000000000893849
INSPECTION AFTER REMOVAL
Mounting Surface Distortion
PBIC3654E
: Engine front
PBIC3774E
: Engine front
PBIC3774E
EM-34
< ON-VEHICLE REPAIR >
[HR16DE]
EXHAUST MANIFOLD
• Using a straightedge (B) and feeler gauge (A), check distortion of
exhaust manifold mounting surface.
• Replace exhaust manifold if outside the limit.
Limit:
.
PBIC3530J
FUEL INJECTOR AND FUEL TUBE
EM-35
< ON-VEHICLE REPAIR >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
FUEL INJECTOR AND FUEL TUBE
Exploded View
INFOID:0000000000893850
CAUTION:
Never remove or disassemble parts unless instructed as shown in the figure.
Removal and Installation
INFOID:0000000000894022
WARNING:
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
REMOVAL
1.
Release the fuel pressure. Refer to
.
2.
Remove intake manifold. Refer to
1.
Quick connector cap
2.
Fuel feed hose
3.
Fuel tube
4.
Fuel tube protector
5.
O-ring (black)
6.
Clip
7.
Fuel injector
8.
O-ring (green)
Refer to
for symbols in the figure.
PBIC3663E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст