Nissan Qashqai (2007-2010). Manual — part 1042
BACK DOOR
DLK-247
< ON-VEHICLE REPAIR >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Exploded View
INFOID:0000000001054832
REMOVAL
ADJUSTMENT
1.
Back door hinge
2.
Back door assembly
3.
Back door lock assembly
4.
Bumper rubber bracket
5.
Back door stay bracket (lower)
6.
Bumper rubber
7.
Back door stay
8.
Back door stay bracket (upper)
9.
Back door striker
Refer to
JMKIA0186ZZ
DLK-248
< ON-VEHICLE REPAIR >
[WITH I-KEY, WITHOUT SUPER LOCK]
BACK DOOR
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000001054826
REMOVAL
1.
Remove the back door finisher inner. Refer to
INT-26, "Removal and Installation"
2.
Remove the back door window glass. Refer to
GW-17, "Removal and Installation"
NOTE:
1.
Back door hinge
2.
Back door striker
3.
Roof panel
4.
Back door outer
5.
Back door glass
6.
Body side outer
7.
Rear bumper fascia
Refer to
for symbols in the figure.
JMKIA0194ZZ
BACK DOOR
DLK-249
< ON-VEHICLE REPAIR >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
It is necessary to remove back door window glass in order to remove harness, because harness connec-
tor interferes with back door window glass pin.
3.
Disconnect the connectors in the back door, and then remove the grommet, and pull out hte harness.
4.
Remove the parcel shelf. Refer to
INT-24, "Removal and Installation"
5.
Remove the high-mounted stop lamp. Refer to
EXL-183, "Removal and Installation"
6.
Remove the grommet (1), and then pull out the washer tube (2) .
7.
Pull the harness out of the back door.
8.
Support the back door lock with the proper material to prevent it
from falling.
9.
Remove the back door stay bracket mounting bolts (A) on the
back door.
10. Remove the back door hinge mounting nuts (A) on the back
door and remove the back door assembly.
CAUTION:
Perform work with 2 workers, because of its heavy weight.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
JMKIA0190ZZ
A
: Jack
B
: Shop cloth
JMKIA0191ZZ
JMKIA0192ZZ
JMKIA0193ZZ
DLK-250
< ON-VEHICLE REPAIR >
[WITH I-KEY, WITHOUT SUPER LOCK]
BACK DOOR
• After installation, perform fitting adjustment. Refer to
DLK-250, "BACK DOOR ASSEMBLY : Adjust-
• Check the back door open/close operation after installation.
• Check the back door lock/unlock operation after installation.
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000001054856
FITTING ADJUSTMENT
1.
Check the clearance and the evenness between the back door and each part visually and by touching.
(Fitting standard dimension in the table below shall be satisfied.)
2.
In case any parts are out of specification, adjust them according to the procedures shown below.
3.
Loosen the bumper rubber.
4.
Loosen the back door striker mounting bolts.
5.
Lift up the back door approximately 100 – 150 mm (3.937 – 5.906 in) height then close it lightly and check
that it is engaged firmly with the back door closed.
6.
Check the clearance and evenness.
7.
Finally tighten the back door striker.
BACK DOOR STRIKER
BACK DOOR STRIKER : Exploded View
INFOID:0000000001091322
Portion
Standard
Difference(RH/LH)
Back door panel –
Roof panel
A – A
F
Clearance
5.0 – 7.0 mm
(0.197 – 0.276 in)
—
G
Surface height
0.0 – 2.0 mm
(0.000 – 0.079 in)
—
Back door glass –
Body side outer
B – B
H
Clearance
3.9 – 8.1 mm
(0.154 – 0.319 in)
2.1 mm (0.083 in)
I
Surface height
- 1.0 – 3.1 mm
(- 0.039 – 0.122 in)
2.0 mm (0.079 in)
Back door panel –
Body side outer
C – C
J
Clearance
3.5 – 6.5 mm
(0.138 – 0.256 in)
2.0 mm (0.079 in)
K
Surface height
- 1.0 – 1.0 mm
(- 0.039 – 0.039 in)
—
Back door panel –
Rear bumper fascia
D – D
L
Clearance
4.0 – 8.0 mm
(0.157 – 0.315 in)
2.0 mm (0.079 in)
M
Surface height
0.1 – 4.1 mm
(0.004 – 0.161 in)
2.1 mm (0.083 in)
Back door panel –
Rear bumper fascia
E – E
N
Clearance
5.8 – 10.2 mm
(0.228 – 0.402 in)
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст