Nissan Qashqai (2007-2010). Manual — part 603
FLUID COOLER SYSTEM
TM-347
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Remove hose clamp (1), and remove CVT water hose B (2).
INSTALLATION
Note the following, and install in the reverse order of removal.
*: Refer to the illustrations for the specific position each hose clamp tab.
• The illustrations indicate the view from the hose ends.
• When installing hose clamps center line of each clamp tab should
be positioned as shown in the figure.
• Insert CVT water hose according to dimension (A) described
below.
• Set hose clamps (1) from the end of fluid cooler hose (2) according
to dimension (A) described below.
• Hose clamp should not interfere with the bulge.
FLUID COOLER
: Clip
JPDIA0123ZZ
CVT water hose
Hose end
Paint mark
Position of hose clamp*
CVT water hose A
Thermostat housing
Facing upward
B
Heater thermostat
Facing forward
C
CVT water hose B
CVT fluid cooler
Facing forward
A
Water outlet
Facing forward
A
D: Front
E: Upper
JPDIA0125ZZ
(1)
(2)
Distance A
CVT water hose A
Thermostat housing
27 mm (1.06 in)
Heater thermostat
CVT water hose B
Water outlet
CVT fluid cooler
End reaches the tube
bend R position.
SCIA7203E
Dimension A
: 5 – 7 mm (0.20 – 0.28 in)
SCIA8123E
TM-348
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
FLUID COOLER SYSTEM
FLUID COOLER : Exploded view
INFOID:0000000000967504
FLUID COOLER : Removal and Installation
INFOID:0000000000967505
REMOVAL
1.
Remove engine under cover.
2.
Remove front bumper assembly. Refer to
3.
Remove air duct (inlet). Refer to
.
1.
Hose clamp
2.
Fluid cooler
3.
Bracket
4.
Fluid cooler hose A
5.
Fluid cooler hose B
6.
Fluid cooler tube
7.
Fluid cooler hose D
8.
Fluid cooler hose C
A.
To CVT fluid cooler
Refer to
for symbols in the figure.
JPDIA0128GB
FLUID COOLER SYSTEM
TM-349
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Remove clip (A).
5.
Remove hose clamp (1) and fluid cooler hose A (2).
6.
Remove hose clamp (3) and fluid cooler hose B (4).
7.
Remove fluid cooler (5).
8.
Remove hose clamp (1) and fluid cooler hose C (2).
9.
Remove hose clamp (3) and fluid cooler hose D (4).
10. Remove fluid cooler tube (5).
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
After completing installation, check for CVT fluid leakage and CVT fluid level. Refer to
B
: Bolt
C
: Nut
: Vehicle front
JPDIA0121ZZ
: Bolt
JPDIA0122ZZ
Fluid cooler hose
Hose end
Paint mark
Position of hose clamp*
Fluid cooler hose A
Fluid cooler side
Facing forward
D
Fluid cooler tube side
Facing to the left of the vehicle
C
TM-350
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
FLUID COOLER SYSTEM
*: Refer to the illustrations for the specific position each hose clamp tab.
• The illustrations indicate the view from the hose ends.
• When installing hose clamps center line of each clamp tab should
be positioned as shown in the figure.
• Insert fluid cooler hose according to dimension (A) described
below.
• Set hose clamps (1) from the end of fluid cooler hose (2) according
to dimension (A) described below.
• Hose clamp should not interfere with the bulge.
Fluid cooler hose B
Fluid cooler side
Facing forward
D
Fluid cooler tube side
Facing to the left of the vehicle
C
Fluid cooler hose C
Fluid cooler tube side
Facing to the Right of the vehi-
cle
C
CVT fluid cooler side
Facing upward
B
Fluid cooler hose D
Fluid cooler tube side
Facing to the Right of the vehi-
cle
C
CVT fluid cooler side
Facing upward
A
Fluid cooler hose
Hose end
Paint mark
Position of hose clamp*
: Upper
JPDIA0126ZZ
(1)
(2)
Distance A
Fluid cooler hose A, B
Fluid cooler
24 mm (0.94 in)
Fluid cooler hose B, C
Fluid cooler tube
33 mm (1.30 in)
Fluid cooler hose C, D
CVT fluid cooler
30 mm (1.18 in)
SCIA7203E
Dimension A
: 5 – 7 mm (0.20 – 0.28 in)
SCIA8123E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст