Nissan Qashqai (2007-2010). Manual — part 461
P0340 CMP SENSOR
EC-1363
< COMPONENT DIAGNOSIS >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace CMP sensor.
ECM
Condition
Voltage
Connector
Terminal
F68
75
(CMP sensor signal)
[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle.
0 - 1V
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm
0 - 1V
MBIB1510E
MBIB1511E
EC-1364
< COMPONENT DIAGNOSIS >
[K9K]
P0380 GLOW RELAY
P0380 GLOW RELAY
DTC Logic
INFOID:0000000001115078
DTC DETECTION LOGIC
NOTE:
• Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC is declared present after attempts have been made to start the engine.
• Special notes:
If the DTC is present, it will be difficult to start the vehicle, or even impossible when cold, or preheating will
be continuous and the heater plugs will deteriorate.
Diagnosis Procedure
INFOID:0000000000956057
1.
CHECK GLOW RELAY POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect glow relay harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between glow relay connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• 80A fusible link (letter N)
• Harness for open and short between glow relay and battery
>> Repair open circuit or short to ground or short to power in harness or connectors.
3.
CHECK GLOW RELAY INPUT CIRCUIT FOR OPEN AND SHORT-I
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between glow relay harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK GLOW RELAY INPUT CIRCUIT FOR OPEN AND SHORT-II
1.
Check the continuity between glow relay harness connector and ECM harness connector.
DTC No.
Trouble diagnosis name
Possible cause
P0380
GLOW PLUG DIAGNOSTIC CONNECTION
• CO: Open circuit
• CC.0: Short circuit to ground
• CC.1: Short circuit to +12V
• Harness or connectors
(The glow relay circuit is open or shorted.)
• Glow relay
Glow relay
Ground
Voltage
Connector
Terminal
F94
4
Ground
Battery voltage
Glow relay
ECM
Continuity
Connector
Terminal
Connector
Terminal
F94
3
F68
80
Existed
P0380 GLOW RELAY
EC-1365
< COMPONENT DIAGNOSIS >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace glow relay.
NO
>> Repair or replace.
Glow relay
ECM
Continuity
Connector
Terminal
Connector
Terminal
F94
8
F68
76
Existed
EC-1366
< COMPONENT DIAGNOSIS >
[K9K]
P0381 GLOW CONTROL SYSTEM
P0381 GLOW CONTROL SYSTEM
DTC Logic
INFOID:0000000001115079
DTC DETECTION LOGIC
NOTE:
• Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC is declared present after several attempts have been made to start the engine.
• Special notes:
If the DTC is present, it will be difficult to start the vehicle, or even impossible when cold, or preheating will
be continuous and the heater plugs will deteriorate.
Diagnosis Procedure
INFOID:0000000001091154
1.
CHECK GLOW RELAY POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect glow relay harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between glow relay connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• 80A fusible link (letter N)
• Harness for open and short between glow relay and battery
>> Repair open circuit or short to ground or short to power in harness or connectors.
3.
CHECK GLOW RELAY INPUT CIRCUIT FOR OPEN AND SHORT-I
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between glow relay harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK GLOW RELAY INPUT CIRCUIT FOR OPEN AND SHORT-II
1.
Check the continuity between glow relay harness connector and ECM harness connector.
DTC No.
Trouble diagnosis name
Possible cause
P0381
GLOW CONTROL UNIT CIRCUIT
• CC.0: Short circuit to ground
• CO.1: Open circuit or short circuit to +12V
• Harness or connectors
(The glow relay circuit is open or shorted.)
• Glow relay
• Glow plug
Glow relay
Ground
Voltage
Connector
Terminal
F94
4
Ground
Battery voltage
Glow relay
ECM
Continuity
Connector
Terminal
Connector
Terminal
F94
3
F68
80
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст